Loading ...
Loading ...
Loading ...
BEVEL STOP ADJUSTMENT
I_ WARNING]
To avoid injury from an accidental start, make
sure the switch is in the OFF position and the
plug is not connected to the power source
outlet.
90° (O°) Bevel adjustment (Fig. N)
1. Loosen bevel lock handle (1) and tilt the
cutting arm completely to the right. Tighten
the bevel lock handle.
2. Place a combination square (2) on the miter
table with the ruler against the table and the
heel of the square against the saw blade.
3. If the blade is not 90° (0°) square with the
miter table (5), loosen the bevel lock handle
(1), tilt the cutting head to the left, loosen the
Iocknut (4) on the bevel angle adjustment
bolt (3) and use a 10 mm wrench to adjust
the stop bolt (3) depth in or out to increase or
decrease the bevel angle.
4. Tilt the cutting arm to back to the right at 90°
(0°) bevel and recheck for alignment.
5. Repeat steps 1 through 4 if further adjustment
is needed.
6. Tighten bevel lock handle (1) and Iocknut (4)
when alignment is achieved.
Fig. N 3
4
2 5
45° Bevel Adjustment (Fig. P)
1. Loosen the bevel lock handle (7) and tilt the
cutting head completely to the left.
2. Using a combination square, check to see if
the blade angle is 45° to the table.
3. If the blade is not at 45° to the miter table, tilt
the cutting arm to the right, loosen the Iocknut
(8) on the bevel angle adjustment bolt (9) and
use a 10 mm wrench to adjust the stop bolt
(9) depth in or out to increase or decrease the
bevel angle.
4. Tilt the cutting arm to the left to 45° bevel and
recheck for alignment.
5. Repeat steps 1 through 4 until the blade is at
45° to the miter table.
6. Tighten bevel lock handle (7) and Iocknut (8)
when alignment is achieved.
Fig.P \
8
33.9 ° Bevel Adjustment (Fig. P)
1. Push the bevel detent pin (10)in toward the
front of the unit.
2. Unlock the bevel lock handle and tilt the
cutting arm to the crown molding positive stop
at 33.9 °.
3. Using a combination square, check to see if
the blade angle is 33.9 °to the table.
4. If the blade is not at 33.9 °to the miter table,
loosen Iocknut (11) and use a 10 mm wrench
to adjust the bolt (12) in or out until the blade
is at 33.9 °to the miter table.
5. Secure the Iocknut (11) into position after
alignment is achieved.
90° Bevel Pointer Adjustment (Fig. O)
1. When the blade is exactly 90° (0°) to the table,
loosen the bevel indicator screw (5) using a
# 2 Phillips screwdriver.
2. Adjust bevel indicator (6) to the "0" mark on
the bevel scale and retighten the screw.
Fig.O
MITER ANGLE ADJUSTMENT (FIG. Q)
The sliding compound miter saw scale can be
easily read, showing miter angles from 0° to
45° to the left, and 0° to 45° to the right. The
miter saw table has nine of the most common
angle setttings with positive stops at 0°, 15°,
22.5 °, 31.6 °, and 45°. These positive stops
position the blade at the desired angle quickly
and accurately. Follow the process below for
quickest and most accurate adjustments.
1. Unlock the miter table by turning the miter
handle (1) counterclockwise.
2. Move the turntable while lifting up on the
positive stop locking lever (2) to align
the indicator (3) to the desired degree
measurement.
Loading ...
Loading ...
Loading ...