Loading ...
Loading ...
Loading ...
Auxiliary controls on your Zoneline.
Auxiliary Controls--Aux Set Button
The auxiliary set controls are located behind
the room cabinet, below the control panel,
Remove the room cabinet, See the To Remove
the Room Cabinet section,
GEAppliances.corn
AuxiliarySet Button
AccessCover
The owner is responsible for ensuring the auxiliary
controls are set to the desired function, There are 9
different modes that can be set using the auxiliary
set button, To change modes, press AUXSET("AU"
appears on the display), Press the mode button on
the control pad until the first digit in the display
shows the number corresponding to the mode you
are choosing and the correct HEAT/COOL LED is lit,
Press the up or down arrow (shown in the second
digit of the display) to make the mode setting
selection where applicable, Press the AUXSET
button to confirm the selection,
R First Digit
I _ 'Z4[
B Load
Shedding
Sentinel
_ ConstantFan
temperature
Limit _ Hgt]]
ClaSS 2Mode
_'_ Duct Mode
AH I2R Mode(AZ61 Only)
Boost Heat
(AZ61 Ortly)
U Second Digit
Press A / v
_,_ -Cycle// _''_ -Continue
-Off /,, f-4 -On
u
COOL HEAT
O; 80F_85F o: 60F°65F
1: 64F=85F 1: 60F-70F
t 2: 66F=85F 2: 60F-72F
3: 68F=85F 3: 60F-74F
4 70F=85F 4: 60F-76F
\\ 5: 72F-85F 5: 60FWSF
\ 6: 74F-85F 6: 60F-80F
"\ 7: 76F=85F 7: 60F-85F
_ On
P..I - off ,,' -
/
_J
[ MODE 1 [ Smart Fan--Cooling/Heating
The default setting for Mode 1 is as follows:
Cooling: Continuous (ON)
Heating: Cycle (OFF)
Press MODEuntil a 1 appears in the first digit of the
display for Smart Fan cool mode, The COOL LED
light on the main control will be on, To change to
heat mode, press MODEagain, The HEATLED light
on the main control will be lit, Press the down arrow
to set the indoor fan to cycle on/off when the unit is
heating or cooling "U ," Press the up arrow to set
the indoor fan to run continuously" 1-1,"This is
shown in the second digit of the display, Press AUX
SETto confirm your selection and exit AUXSET
mode, or press MODEto continue setting other
functions,
*Note: In cyclic cooling mode, the indoor fan will activate occasionally to
verify airtemperature in the room, In cyclic heating mode, the fan will
continue to operate for 90seconds after the heating function has stopped in
order to increase unit efficiency,
-- HIGH
-- LOW
-- AUTO
Cooling- Cycle_
r_ HIGH
-- LOW
-- AUTO
Cooling- Continuous
-- HIGH
-- LOW
-- AUTO
Heating- Cycle_
r_ HIGH
.... -- LOW
{ : -- AUTO
Heating- Continuous
_COOL
-- FAN
-- HEAT
_COOL
-- FAN
-- HEAT
--COOL
-- FAN
HEAT
--COOL
-- FAN
HEAT
[ MODE 2 Load Shedding (Central Desk Control)
The default setting for Mode 2 is OFF,
Thisfeature is active only if the unit is connected to a
CDCand the CDC has control, Press MODEuntil a 2
appears in the first digit of the display for Load
Shedding mode, Press the down arrow for OFF "u" or
the up arrow for ON "rl ,"This is shown in the second
digit of the display, When this mode is on, only the
indoor fan can be turned ON or OFFwith the unit
controls, When this mode is off, all operation is disabled
except Heat/Freeze Sentinel (Mode 3),PressAUXSETto
confirm your selection and exit AUXSETmode, or
press MODEto continue setting other functions,
Load
Shedding
OFF
Load
Shedding
ON
5
Loading ...
Loading ...
Loading ...