Loading ...
3
7
4
5
6
1
2
2
Para ordenar Repuestos, Sírvase Llamar al Concesionario
má s Cercano a su Domicilio
1 Juego de piezas del flotante 60038-001 60038-001 60042-001 60038-001 60038-001
2 Piezas de la cubierta superior 60017-001 60017-001 60040-001 60017-001 60017-001
3 Estator 32064-S01 32074-S01 32050-S04 32064-S01 32074-S01
4 Ensamblaje de la abrazadera inferior/ Rotor 60002-001 60003-001 60003-002 60002-001 60003-001
5 Placa dell impulsor 15958 15958 15958 15958 15958
6 Impulsor 60000-001 60001-001 60001-001 60000-001 60001-001
7 Voluta 60007-001 60007-001 60007-001 60039-001 60039-001
Lista de Repuestos
No. de Para los Modelos:
Ref. Descripció n SPF33 SPF50 SSPF50 CDU790 CDU800
MODELOS
CDU
SSCDU
FLS
1 Juego de piezas del flotante 60038-001 60042-001 60042-001 60038-001 60038-001
2 Piezas de la cubierta superior 60017-001 60040-001 60040-001 60082-001 60082-001
3 Estator 32064-S01 32050-S04 32050-S04 32064-S01 32050-001
4 Ensamblaje de la abrazadera inferior/ Rotor 60002-001 60081-001 60003-002 60002-001 60003-001
5 Placa del impulsor 15958 15958 15958 15958 15958
6 Impulsor 60000-001 60001-001 60091-001 60000-001 60001-001
7 Voluta 60039-001 60039-001 60039-001 60039-001 60039-001
No. de Para los Modelos:
Ref. Descripció n CDU790HH CDU980 SSCDU800 FLS790 FLS800
Sírvase proporcionar la siguiente informació n:
- Nú mero del modelo
- Nú mero de serie (si lo hubiere)
- Descripciones y nú mero de repuestos, tal como
aparecen en la lista de piezas.
Direcció n para correspondencia sobre piezas:
Wayne Water Systems
100 Production Drive
Harrison, OH 45030 U.S.A.
FLS790, FLS800, SPF33, SPF50, SSCDU800, SSPF50,
CDU790, CDU790HH, CDU800 y CDU980
MODELOS
CON
ALARMA
Installation
(Continued)
to secure pump could allow pump
movement and switch interference
and prevent pump from starting or
stopping.
3. Thread (optional) check valve into
pump body carefully to avoid
stripping or cross threading.
Do not use pipe joint sealant.
4. Connect 1-1/4" rigid pipe to rubber
boot on check valve. Reverse boot
for 1-1/2" diameter pipe.
Tighten hose clamps.
Support pump and piping when
assembling and after installation.
Failure to do so could cause piping to
break, pump to fail, etc. which could
result in property damage and/or
personal injury.
5. Protect electrical cord from sharp
object, hot surfaces, oil and
chemicals. Avoid kinking the cord
and replace damaged cords
immediately.
6. A sump pit cover must be installed to
prevent debris from clogging or
damaging the pump.
FLOOD ALERT MODELS (SEE FIGURE 2)
1. Remove battery access door and
connect a 9 volt battery to battery
terminal. Replace battery access
door.
!
WARNING
4 Sp
Operation
Always disconnect the power
source before attempting to
install, service, relocate or
maintain the pump. Never
touch sump pump, pump
motor, water or discharge
piping when pump is
connected to electrical
power. Never handle a pump
or pump motor with wet
hands or when standing on
wet or damp surface or in
water. Fatal electrical shock
could occur.
1. A ground fault circuit interrupter
(GFCI) is required (See Figure 2).
Risk of electrical shock! This pump is
supplied with a grounding conductor
and grounding type attachment plug.
Use a grounded receptacle to reduce
the risk of fatal electrical shock.
IMPORTANT: Never cut off the round
grounding prong. Cutting the cord or
plug will void the warranty and make
the pump inoperable.
2. This pump is only for use on 120 Volt
(single-phase), 60 hz, 15 amp service
and is equipped with a 3-conductor
cord and 3-prong, grounding type
plug.
3. Insert the pump power cord plug
directly into outlet (See Figure 2).
!
WARNING
!
DANGER
2
Operating Instructions and Parts Manual
Manual de Instrucciones de Operació n y Piezas
4. Fill sump with water. The pump will
start automatically when the water
has filled the sump to a depth of
approximately 9". The pump will
stop when the water depth is
approximately 4". The pump will
recycle thereafter as required.
5. Do not operate the pump unless it is
submerged in water. Dry running
causes pump failure.
6. The motor is equipped with an
automatic reset thermal protector.
7. While the pump is draining the pit,
verify that the discharge piping is
carrying the water to a point several
feet away from the foundation.
8. If pump discharge line is exposed to
freezing temperature, the exposed
line must be pitched to drain.
Trapped water will freeze and
damage the pump.
FLOOD ALERT MODELS (SEE FIGURE 2)
1. Unit should be plugged into outlet
as shown in Figure 2. Do NOT plug
unit in upside down. Doing so may
cause pump to unplug. If your
receptacle is upside down, have a
qualified electrician reposition the
outlet before installing the unit.
2. Testing Alarm: Press and hold test
button until alarm sounds. If alarm
does not activate after 3 seconds,
check and/or replace battery then
repeat test.
FLS790, FLS800, SPF33, SPF50, SSCDU800, SSPF50,
CDU790, CDU790HH, CDU800 & CDU980
www.waynepumps.com
TEST
RESET
TEST
RESET
MODELS CDU, SPF, SSPF, SSCDU
Power
Cord
Grounding
Blade
TEST
RESET
TEST RESET
FLOOD ALERT MODELS
Battery
Door
Test
Button
Back of
Unit
Front of
Unit
Figure 2 - Required GFCI Outlets and Optional Positions
Loading ...
Loading ...
Loading ...