Loading ...
Loading ...
Loading ...
7. Makesuregardenhoseisconnectedtowaterinlet.
Checkthathighpressurehoseisconnectedtospraygun
andpump.Turnonwater.
You must attach alI hoses before
Starti_gthe enginewithoutall the hosesconnectedandwithout
the waterturnedONwill damagethe pump.
Darnageto eqdpmentresultingfrom failureto followthis
instructionwill void warranty.
8. Engagetrigger iock on spray gun and start engine
foiiowing instructions How to Start Your Pressure
Washer.
9£ If using cteaning tank, rotate detergentshut-off valve on
cleaning tank to "On" position (A).
/
f
IMPORTANT:If using detergent siphoning hose, make sure
detergent shut-off valve ell cleaning tank is in the "Off"
position.
9B. If using detergent siphoning hose, placesmall filter end
of detergentsiphoning tube into detergentcontainer.
NOTE:Make sure the filter is fully submerged in detergent
while applying detergent.
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube.
Wheninsqting the filter into a detergentsolutionbottle,route
the tubeso asto keepit from inadvertently'contactingthe hot
rnuffler.
10. Appiy HydroFoamTM washto a dry surface, starting at
lower portion of areato be washed and work upward,
using iong, even,overlapping strokes.
NOTE:To prevent water spotting on vehicles,work in a
shaded areaand allow surfaces to coot before beginning.
11. Allow HydroFoamTM wash to soak in between
3-5 minutes before washing and rinsing. Reappiy as
neededto prevent surface from drying. DO NOTailow
HydroFoamTM wash to dry on (prevents streaking).
For best resuits, scrub the HydroFoamTM wash covered
surface to heip remove stubborn dirt, grime and stains. For
vehicles, use a soft car wash brush or mitt. For decking,
siding and concrete, use a brush appropriate for the type of
surface being cleaned.
IMPORTANT:When using the detergent siphoning hose, you
must flush the detergent siphoning system after ea@ use by
placing the fiiter into a bucket of clean water, then run the
pressure washer in low pressure for 1-2 minutes.
Pressure Washer Rinsing
AfterNydroFoamTM washis applied, s¢onrthe surfaneand rinse
it deae as fdbwn:
1. Engagetrigger lock on spray gun.
2. Makesure detergent shut=off vaive is in "Off" position.
3. Remove HyrdoFoamTM Launcherfrom nozzteextension.
4. Seiectand instaii desired ProjectPro@nozzle,as
described in How to Use ProjectPm@ NozzleSystem.
5. Keepspray gun a safe distance from spray surface.
WARNING
Kickbackfrom spray gun can cause you to fail.
6.
* Operatepressurewasherfrom astablesurface.
, Beextremelycarefulif you mustusethe pressurewasherfrom
a ladder,scaffolding,or anyothersimilarlocation.
o Firmlygraspspraygunwithboth handswhenusing high
pressuresprayto avoidinpry whenspraygunkicksback.
Apply a high pressure spray to a small areaand then
check the surface for damage.If no damage,proceed to
step 7.
Start at top of area to be rinsed, working down with
same overlapping strokes used for cleaning.
Autemati¢ Cod Dewu System (Thermal Relief}
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures above
125°F. The system engagesto cool the pump by discharging
the warm water onto the grennd.
15
Loading ...
Loading ...
Loading ...