Loading ...
Loading ...
Loading ...
Spray Tip aairlterlarlce
A pulsing sensation felt while squeezingthe spray gun trigger
may be causedby excessive pump pressure. The principal
causeof excessive pump pressure is a spray tip clogged or
restricted with foreign materials, such as dirt, etc. To correct
the problem, immediately clean the spray tip following these
instructions:
.
2.
Shut OFF(0) engine and turn off water supply.
ALWAYSpoint spray gun in a safe direction, press red
button and squeezespray gun trigger to releaseretained
high water pressure.
_ikWARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which could result in
serious injury.
o Keephighpressurehoseconnectedto pumpandspraygun
whilesystemis pressurized.
, ALWAYSpointspraygunin safedirection,pressredbutton
andsqueezesprayguntriggerto releasehighpressure,every
timeyou stopengine.
.
4.
Remove spray tip from end of nozzleextension.
Use a small paper clip to free any foreign material
clogging or restricting spray tip (A).
• , /-"
.
6.
Remove nozzleextension from spray gun.
Using a garden hose, remove additional debris by back
flushing water through nozzleextension. Backflush
between 30 to 60 seconds.
7. Reinstall spraytip into nozzleextension.
8. Reconnect nozzleextension to spray gun.
9. Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
10. Start enginefollowing instructions How to Start Your
Pressure Washer.
11. Test pressurewasher by operating with each quick
connect spray tip.
O-Ring Maintenance
PurchaseanO-Ring RepairKit, Searsitem 75116, at your local
Searsor by calling 1o888o331o4569or online at www.sears.
com. it is not included with the pressure washer. This kit
includes replacement o-rings and a water inlet filter. Referto
the instruction sheet provided in the kit to service your unit's
o-rings.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
o NEVERrepairbakingconnectionswithsealantof any kind.
Replaceo=ringor seal.
ENGINEMAINTENANCE
,A WARNING Unintentional sparking could causefire or
electric shock resulting in death or
serious injury.
WHENADJUSTINGOR MAI(INGREPAIRSTO YOUR PRESSURE
WASHER
o Disconnect the spark plug wire from the spark plug and place
the wire where it cannot contact spark plug.
WHENTESTINGFOR ENGINESPARK
o Useapproved spark plug tester.
° DONOTcheckfor spark with spark plug removed.
Oil
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF,SG,
SH SJ or higher. DO NOTuse special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Usethe chart to select the best viscosity for the
outdoor temperature range expected.
14
-,,%::::::::::::::::::::::::::::::::::::::::::::
iSi:i:i:i:i:i:i:i:i
:::::::::::::::::::::
[. iiiii iiii
:i:i:i_i:i:i.-N
* Below40°F (4°C) the use of SAE 30 will result in hard starting.
** Above 80°F (27°C) the use of 10W30 may cause increased oil
consumption. Check oil level more frequently.
2O
Loading ...
Loading ...
Loading ...