Loading ...
Loading ...
Loading ...
| KEY DIMENSIONS AND SPECIFICATIONS
Description Front-Loading VVasher
Rated Voltage/Frequency 120VAC, 60Hz
Dimensions 27 in. (W) X 29 3/_in. (D) X 38 11/16in. (H), 51 in. (D, door open)
68.6 cm (W) X 75.6 cm (D) × 98.3 cm (H), 129.5 cm (D, door open)
Net Vv'eight 202.8 Ib (92kg)
CHOOSE THE PROPER LOCATION
WARNING
• This washer is heavy. Two or more people are
required when moving and unpacking the washer.
Failure to do so may result in damage to property or
serious bodily harm.
• Store and install the washer where it will not be
exposed to temperatures below freezing or exposed
to outdoor weather condfflons. Failure to follow this
warning can cause seriousinjury, fire, electric shock,
or death.
• Properly ground the washer to conform with all
electric governing codes and ordinances. Failure
to follow this warning can cause seriousinjury, fire,
electric shock, or death.
*To reduce the risk of electric shock, do not install the
washer in humid spaces. Failure to follow this warning
can cause serious injury, fire, electric shock, or death.
•To ensure proper air flow, do not block the large
opening on the boflom of the washer with carpeting
or other materials.
• Do not remove the ground prong. Do not use an
adapter or extension cord. Plug into a grounded
3-prong outlet. Failure to follow this warning can cause
serious injury, fire, electric shock, or death.
NOTE: Installing the washer in a humid space, or installing or
storing the -washerwhere it will be exposed to the weather
or freezing temperatures, may result in rustor other
damage that is not covered by the product warranty.
Power O_let
•The power outlet must be within 60 in. (1.5 m) of either
side of the washer.
•The appliance and outlet must be positioned so that
the plug is easily accessible.
• Do not overload the outlet with more than
one appliance.
*The outlet must be grounded in accordance with
current wiring electric codes and regulations.
• Time-delay fuse or circuit breaker is recommended.
NOTE: It is the personal responsibility and obligation of
the product owner to have a proper outlet installed by a
qualified electrician.
FLOORING
•To minimize noise and vibration, the washer MUST be
installed on a solidly constructed floor. See the NOTE
to your right.
•Allowable slope under the entire washer is a maximum
1 in. difference from side to side or from front to back.
• Installing on carpeting and soft tile surfaces is
not recommended.
° Never install the washer on a platform or weakly
suppofled structure.
7
CLEARANCES
I
29 3/4" _ 4"
(75.6 cm) _-_! (10 cm)51"
(129.5 cm)
To ensure sumcient clearance for water lines and airflow,
allow minimum clearances of at least 1 in_(2.5 cm) at the
sides and 4 in. (10 cm) behind the unit. Be sure to allow
for wall, door, or floor moldings that may increase the
required clearances.
27,,
(68.6 cm)(2,5 cm) (2.5 cm}
Allow at least 22 in. (55.9 cm) in front of
the washer to open the door.
NOTE: The floor must be strong and rigid enough to
support the weight of the washer, when fully loaded,
without flexing or bouncing. If your floor has too much
flex, you may need to reinforce it to make it more rigid.
A floor that is adequate for a top-loading washer may
not be rigid enough for a front loading washer, due to
the difference in the spin speed and direction, if the
floor is not solid, your washer may vibrate and you may
hear and feel the vibration throughout your house.
Loading ...
Loading ...
Loading ...