User Manual Kwikset 99140-009 99140-008 SmartCode 914 Keypad Keyless Entry Zigbee Smart Lock Connected Deadbolt Door Lock Featuring SmartKey Security in Venetian Bronze

Kwikset 99140-009 99140-008 SmartCode 914 Keypad Keyless Entry Zigbee Smart Lock Connected Deadbolt Door Lock Featuring SmartKey Security in Venetian Bronze - Use Manual - Use Guide PDF.
Documents: Go to donwload!
User Manual
  • Owner's manual - (English)
Other Documents
  • User Guide - (English)
  • Application Guide - (English)


2-1/8"

54 mm

1-1/2"

38 mm

What is the diameter of the hole in the door?

Remove battery cover and battery pack from interior assembly.

Install 4 AA batteries in battery pack.

Install interior assembly onto mounting plate.

Press and HOLD the Lock button while installing battery pack.

Hold button until the latch bolt starts moving on its own.

Did the latch bolt retract and extend on its own when the battery pack was installed?

Locate screws for step 3C and keep them within reach.

Install exterior keypad and mounting plate.

Diameter is 2-1/8" (54 mm)

Diameter is 1-1/2" (38 mm)

“D” is required for installation.

Install “D” on “E”. “D” is not needed for installation. Discard “D”.

Cable goes underneath latch.

Support exterior assembly during mounting plate installation.

Route cable through center hole. then push cable into bottom hole.

Insert key and test latch. If latch does not extend or retract smoothly. adjust screws (P).

Remove key when finished and make sure the latch bolt is fully extended.

Keep parallel to edge of door.

Tighten screws evenly.

Make sure turnpiece is in the vertical position.

Door handing process was successful! Proceed to next step after latch bolt stops moving.

Remove battery pack. wait 15 seconds. then attempt the process again.

Note: Latch bolt will only retract half way.

Make sure turnpiece shaft is rotated as shown.

Ensure correct polarity.

For best results. use new. non-rechargeable Alkaline batteries only.

Do not install batteries until step 5.

Ensure tight cable connection.

Lay excess cable flat inside the bottom of the interior housing.

(2x)

P (2x)

Install the exterior keypad

Install the interior assembly

Install the batteries and perform the door handing process

This step will teach your lock the orientation of your door and is crucial to lock operation.

Initiate the pairing process at your smart home controller. Refer to your smart home system instructions for more information.

Note: See supplied flyer for provider websites and contact information as applicable.

When prompted by your smart home system to initiate pairing at the lock. press button “A” on the lock interior four times.

If the pairing process is successful. re-name the lock in your system (if applicable).

If the pairing process is unsuccessful. press button “B” nine times.

Perform steps 6A-6C again.

If pairing is still unsuccessful. consult the SmartCode 914 Programming and Troubleshooting Guide online at www.kwikset.com.

Pair the lock with your smart home system

Re-key the lock (if needed).

Install the battery cover.

Confirm that the code(s) added in step 7 can unlock the door.

One green flash with one beep Three red flashes with three beeps

IMPORTANT: Remove battery pack before re-keying.

Make sure the door is open. Press the Program button once.

Locking the Door Unlocking the Door

Enter user code. A total of 30 user codes may be programmed.

Press Lock button once.

Did the keypad flash green once with one beep or flash red three times with three beeps*?

Each user code must be a unique code between 4 and 8 digits. depending on your smart home system.

Programming was successful.

Proceed to step 8.

Programming was unsuccessful.

Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt.

Make sure the lock has room for an additional code. If all user code positions are filled. delete a code to make room for this one.

Press Lock button once.

Enter user code.

It is recommended that you add and delete all user codes through your smart home control system. If your system does not allow this. codes may be added directly to the lock as shown here.

Mastercode For enhanced security. a mastercode may be used when adding and deleting user codes. For more information about the mastercode. download the SmartCode 914 Programming and Troubleshooting Guide at www.kwikset.com.

Programming Timeout During programming. if no button is pressed for five seconds. the system will time out (indicated by three beeps and a red flashing keypad). and you will need to restart the procedure.

+Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon.

R (3x)

Re-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information.

Keep “G” in a safe place. as you will need it to access the back panel for additional programming.

Reinstall battery pack.

Add user codes

Re-key the lock (if needed) and install the battery cover

Test the lock (review normal operation)

Alert Reason Solution

Keypad flashes green once with one beep*.

Successful programming.

N/A

Keypad flashes red once with one beep*.

One incorrect code entered.

Re-enter code.

Keypad flashes red three times with three beeps*.

No user code programmed.

Program at least one user code.

Programming timeout after five seconds.

Attempt programming procedure again.

Unsuccessful programming.

Keypad flashes red 15 times with 15 beeps* Three incorrect codes entered within one minute.

Re-enter code after 60 second keypad lockout.

Keypad flashes red with fast beeping sound for three to four seconds.

Low battery.

Replace batteries.

Keypad flashes red with continuous beeping sound for two seconds.

Door jammed while attempting to lock.

Manually re-lock door. If needed. reposition strike.

Lock beeps continuously.

Interior assembly is disconnected from exterior.

Remove battery pack. reconnect the interior to the exterior. then reinstall battery pack.

+Beeping sound will only be heard if switch #3 is on.

Adding the lock to the network

During the pairing process. press button “A” on the lock interior four times.

Removing the lock from the network

Press button “B” on the lock interior nine times.

+ 2015 Kwikset Corporation

Read all instructions in their entirety.

2. Familiarize yourself with all warning and caution statements.

Remind all family members of safety precautions.

4. Protect your user codes and mastercode.

Dispose of used batteries according to local laws and regulations.

CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes. you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge.

The use of a mastercode can help protect your system’s settings.

WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means. or evaded by entry elsewhere on the property. No lock can substitute for caution. awareness of your environment. and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk. you should consult a qualified locksmith or other security professional.

Network Information Important Safeguards

ZigBee System Notes

ZigBee is a “Wireless mesh network. and results may vary based on building construction and communication path. with 35+ feet being typical installed distance in a standard home environment and 250 feet+ when the lock has a clear line of sight with the smart home controller. It may be necessary to install additional ZigBee devices to enhance the communication path between the lock and controller for a more robust ZigBee network.

If no button is pressed for five seconds. the system will time out. and you will need to restart the procedure.

1 Keep door open.

Press Program button once.

5 Re-enter user code.

6 Press Lock button once.

If unsuccessful

Make sure to enter the same valid code in steps 3 and 5.

Test code

While the door is open. test the user code to make sure it no longer unlocks the door.

2 Press Lock button once.

4 Press Lock button once.

3 Enter user code to be deleted.

SmartCode at a Glance

Deleting a single user code

Note: All codes may be deleted at once if the mastercode is enabled. For more information about the mastercode. consult the SmartCode 914 Programming and Troubleshooting Guide at www.kwikset.com.

Reference Guide

Exterior

Back panel

Program button

Status LED

Switches

Turnpiece shaft

Note: When the cover is removed. the turnpiece shaft can be used to manually lock and unlock the door.

Interior (cover removed)

Switches and Status LED colors Troubleshooting

Switch Function

Door lock status LED blinks every 6 seconds

Lock automatically re-locks door 30 seconds after unlocking. Disabled if no codes are programmed.

Audio

Not used.

Color Lock Status

Blinking green Unlocked

Blinking amber Locked

Blinking red Low battery

Solid red

Door handing process did not work properly.

See the online Programing and Troubleshooting Guide.

1 2 3 4

Switches

Status LED

System Alerts

Factory Reset

A factory reset will delete all codes associated with the lock. and it will remove it from your smart home system.

Status LED

1 Remove battery pack.

2 Press and HOLD the Program button while reinserting the battery pack.

Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.

Keypad

Lock button

Keyway SmartKey tool hole

Button “A” Button “B”

3 Press the Program button once more. When the LED flashes green and you hear one beep. the lock has been reset.

4 Perform the door handing process again to teach the lock the orientation of the door. pair the lock with your smart home system. and add user codes to your lock.

A complete SmartCode 914 Programming and Troubleshooting Guide is available at www.kwikset.com.



Newest Added: 99140-102 99100-077 98880-004 98880-005 99170-004

Tags: Kwikset 917, Kwikset SmartCode 913

Kwikset 99140-009 | File type: PDF | Filename: 34567300_99140-009.pdf | Size: 4.71 MB | Language: English | Other documents: 2 files.

Download User Manual

Product Infomation and Reviews - 99140-009 photo

99140 009 Photo

T: @manualsFile

https://manualsFile.com