FOR PRODUCT WITH A HOME AREA NETWORK
(HAN) GATEWAY SYSTEM CONNECTION.
1. Please make sure you have followed all the steps in the
lock Installation and Programming Manual.
4. User Code Information:
● Code or codes that are programmed before the installation of the daughter
card will be disabled.
● Code or codes that are programmed after the installation of the daughter
card will remain valid.
● Once the lock has been included into the (HAN) system, you can program up
to 30 codes.
● We suggest you add and change codes from the system controller.
● Deleting a code can only be done from the system controller.
3. For inclusion or exclusion of the lock, refer to the Home Area Network (HAN)
system instructions and note functions referred to in Figure 2 and the chart below.
2. Make sure the RF daughter card is properly installed,
seated and connected, see Figure 1, callout .
Light (under the reference card)
will illuminate Yellow for 5 seconds
during the Inclusion process and will
illuminate Red for 5 seconds during
the Exclusion process.
POUR UN PRODUIT COMPRENANT
UNE CONNEXION À UN SYSTÈME DE
COMMUNICATION INTER-RÉSEAU
DOMESTIQUE.
1. Veuillez vous assurer de suivre toutes les étapes dans le Guide de
programmation et d'installation du serrure.
3. Pour inclure ou exclure le serrure, veuillez consulter les instructions
du système de réseau domestique et prenez note des fonctions
dont on fait référence à la Figure 2 et le tableau dessous.
2. Veuillez vous assurer que la carte fille RF est correctement installée,
bien fixée et connectée, consultez la Figure 1, point .
La lumière (sous la carte
de référence) s'allumera en
Jaune pendant 5 secondes
au cours du processus
d'inclusion et elle s'allumera
en Rouge pendant 5
secondes au cours du
processus d'exclusion.
4. Information sur le code d'utilisateur:
● Le code ou les codes qui sont programmés avant l'installation de la
carte fille seront désactivés.
● Le code ou les codes qui sont programmés après l'installation de la
carte fille resteront activés.
● Une fois le serrure inclus dans le système inter-réseau domestique,
vous pouvez programmer jusqu'à 30 codes.
● Nous vous suggérons d'ajouter et de changer les codes du contrôleur
de système.
● La suppression d'un code ne peut être effectuée qu'à partir du
contrôleur de système.
CONFORMITÉ RÈGLEMENTAIRE
Ce produit est conforme aux normes établies par les organismes de
règlementation suivants :
• Federal Communications Commission (FCC, États-Unis)
• Industrie Canada
Copyright © 2009 Black & Decker Corporation
Fig. 2
C
C
A
A
A
Fig. 1
RF
Protocol
Zigbee
Z-Wave
Inclusion
Process
D
B
B
B
Button used in
Exclusion
Process
Button used in
Protocole
RF
Zigbee
Z-Wave
Processus
De Inclusion
D
B
B
B
Bouton utilisé
pour le
Bouton utilisé
pour le
Processus
De Exclusion
REGULATORY COMPLIANCE
This product complies with standards established by the following regulatory bodies:
• Federal Communications Commission (FCC)
• Industry Canada
FCC
FCC ID: NUL5024093ZGB (Wireless Lock Module 5024093)
FCC ID: NUL5024095ZWV (Wireless Lock Module 5024095)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: ( 1 ) this device may not cause harmful interference, and
( 2 ) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communi-cations. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT! Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
INDUSTRY CANADA
This Class B digital apparatus complies with Canada ICES-003. CAN/CSA-C22.2 NO.
14-05 (Industrial Control Equipment) Operation is subject to the following two conditions: (
1 ) this device may not cause interference, and ( 2 ) this device must accept any interfer-
ence, including
interference that may cause undesired operation of the device.
Canadian ID IC: 3022A-5024093ZGB
Canadian ID IC: 3022A-5024095ZWV
Z-WAVE
• Security enabled Z-Wave product
• Security enabled Z-Wave controller must be used in order to fully utilize product.
This Z-Wave-enabled door lock can be included, operated, and is fully interoperable with
any Z-Wave secure controller.
For more information, visit:
http://www.Kwikset.com/wirelesslocks/products.aspx
ENGLISH
INSTRUCTIONS
D'INSTALLATION
FRANÇAIS
INSTALLATION
INSTRUCTIONS
44571-02
1 / 2
Press program button below once to enter
the 1st code & twice for the 2nd code
Enter code on exterior keypad
Press on exterior keypad to set code
READY
PROGRAM
BUTTON
B
D
C
Loading ...