Loading ...
Loading ...
Loading ...
en Before using for the first time
12
Setting Water hardness in
mmol/l
German hardness in
°dH
French hardness °fH
0 (softened)
1
- - -
1 (soft) Up to 1.5 Up to 8.4 Up to 15
2 (moderately hard) 1.5-2.5 8.4-14 15-25
3 (hard) 2.5-3.8 14-21.3 25-38
4 (very hard)
2
Above 3.8 Above 21.3 Above 38
1
Only set this if you will be using solely softened water.
2
Also set for mineral water. Only use non-carbonated mineral water.
6.2 Initial use
When the appliance is connected to the power supply
for the first time or following a lengthy power failure, the
settings that you will need to configure before you can
use it will appear.
Notes
¡ You can change these settings at any time by going
to the basic settings.
→"Basic settings", Page22
¡ You can also use HomeConnect to configure the
settings. If your appliance is connected, follow the
instructions in the app.
Setting the language
1.
Connect the appliance to the power supply.
a The first setting will appear after a few seconds.
2.
Use the
button to navigate to the bottom row.
3.
Use the or button to select the language.
4.
Use the button to navigate back to the top row.
5.
Use the button to select the next setting.
Setting the time
1.
Use the
button to navigate to the bottom row.
2.
Use the or button to select the correct hour.
3.
Use the button to navigate to the next row.
4.
Use the or button to select the correct number of
minutes.
5.
Use the button to navigate back to the top row.
6.
Use the button to select the next setting.
Setting the date
1.
Use the
button to navigate to the next row.
2.
Use the or button to select the correct day.
3.
Use the button to navigate to the next row.
4.
Use the or button to select the correct month.
5.
Use the button to navigate to the next row.
6.
Use the or button to select the correct year.
7.
Press the button repeatedly until "Date" appears.
8.
Use the button to apply the settings.
Setting the water hardness
1.
Use the
button to navigate to the bottom row.
2.
Use the or button to select the water hardness
range.
→"Before using for the first time", Page11
3.
Use the
button to navigate back to the top row.
4.
Use the button to save your settings.
5.
Open and close the appliance door once.
a The appliance will perform a self-test, after which it
will be ready to use.
a Initial configuration is now complete.
6.3 Calibrating and cleaning the appliance
You will need to calibrate the appliance and clean the
cooking compartment and accessories before using it
to cook food for the first time.
Note:The boiling point of water depends on the air
pressure. During the calibration process, the appliance
makes adjustments to adapt it to the pressure condi-
tions in the location where it is installed.
Requirement:The cooking compartment must have
cooled down completely.
1.
Remove the product information, accessories and
any leftover packaging (e.g. polystyrene pellets)
from the cooking compartment.
2.
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
3.
Press
to switch the appliance on.
→"Switching on the appliance", Page13
4.
Fill the water tank.
→"Filling the water tank", Page14
5.
Set the required type of heating, temperature and
cooking time for the calibration process and press
to start.
→"Steam", Page15
Calibration
Type of heating Steam
Temperature 100 °C
Duration 30minutes
Tip:Do not open the appliance door while calibra-
tion is in progress. Calibration will otherwise be in-
terrupted.
a Calibration starts. This generates a lot of steam.
6.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures
above 120°C, this will damage the enamel.
▶ Do not use the appliance if there is water on the
cooking compartment floor.
▶ Wipe away any water on the cooking compart-
ment floor before operation.
Allow the appliance to cool down and then wipe
away the water from the cooking compartment floor.
7.
Set the required type of heating and temperature for
the heat-up process and press
to start.
→"Setting the type of heating and temperature",
Page13
Loading ...
Loading ...
Loading ...