Loading ...
Loading ...
Loading ...
12 English
Range Hood Use and Care
Range Hood for ADA Compliance
Range hoods can be installed to comply with Sections 308 and 309 of
ADA Guidelines, when used with appropriately mounted controls installed
at 15” (38.1 cm) to 40” (101.6 cm) above the oor and control access
does not require reaching over a cooking appliance.
This range hood model NK30B3000US/AA can work in an ADA Compliant
situation when the range hood is wired to operate from a dedicated,
standard electrical wall switch. To facilitate this application, share the
information on the following pages with your electrician when preparing
for the installation.
NOTE
All the models can be controlled by only one remote switch (The switch
activates or deactivates the motor and the light of the hood).
WARNING
All electrical work must be done in accordance with local codes,
ordinances, or the national electrical code as applicable. For safety, this
product must be installed in a grounded switch box. The electrical wiring
installation must be done by a qualied technician.
WARNING
Electrical Shock Hazard
Turn off power at the circuit breaker panel or fuse box before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
(L, ground)
D
E
B
C
F
G
H
E
A
(N, ground)
POWER SUPPLY HOME
G
A. Range Hood Cable
B. UL listed wire connector
C. White wires (N)
D. Black wires (L)
E. Green (or bare) and
yellow-green ground
F. UL listed switch
G. Home power supply cable
H. Deep single gang switch box
WARNING
To avoid re or electrical shock, turn off power at the circuit breaker
panel or fuse box. Conrm that the power is off before wiring.
1. MOUNT THE SWITCH BOX . Install a 3½” deepsingle gang switch
box
2. ATTACH THE POWER CABLE. Clamp wiring to the switch box and
unit using an appropriate clamp. Provide 6” leads inside the box and
fan for easier wiring.
3. CONNECT THE WIRING. General instructions:
• Make sure both the switch box and the appliance are properly
grounded.
• Make sure the ground wire is securely fastened to the control’s
ground screw. Tighten the ground screw.
• Use proper wire nut sizes for the number and size of the wires.
• For push-in and screw terminals: Use min. #14 AWG solid copper
wire only.
• Tighten the screw terminals.
• Make electrical connections following the appropriate diagram.
BK
For ADA compliance add these
elements during the installation
Remote Switch
Ph
L
BK
G
GROUND SCREW
Motor Characteristics
Power supply
120 VAC
Frequency
60 Hz
Amperage
0.65 ±10% A
Wattage Rating
38 ±10% Watts
Motor Resistance
Brown - White
16.98 ±10% Ohms
Brown - Red
9.36 ±10% Ohms
>85
-1.5
+1.5
-1
+1
0÷85
25/10/21
Luis Salazar
10/03/21
PRINTING AREA
(101.6X101.6mm)
RELEASED
* DO NOT PRINT DASHED LINE
Schema elettrico / Wiring diagram
Carta metallizzata 101.6x101.6 / Metallic Sticky Paper x
SEL0176114
Nero / Black
3:2
PIRITE SAMSUNG C19
C19
SEL0176114
For supply connection
use wires suitable
for at least 75° (167°F)
INPUT: 120VAC
+
-
OUTPUT:700mA(2-15VDC)
LED DRIVER
LED
LED
BU
YL
BK
RD
WH - BL
BR
BK
RD
BK
LIGHT SWITCH
ON - OFF
MOTOR SWITCH
LOW - OFF - HIGH
N
WH
SPEED 2
COMMON
SPEED 1
BR
WH
RD
BK
4. MOUNT THE CONTROL IN THE SWITCH BOX. Tuck wires into
the switch box and fasten the control to the box using the attached
screws.
5. ATTACH THE SWITCH PLATE. Fasten the switch plate to the control
using the short screws from the parts bag.
Range Hood use and Care
Loading ...
Loading ...