Loading ...
Loading ...
Loading ...
8 17
AIR CAP SET SELECTION
Six additional size Setups are available as accessories. Size No.3
(1.3mm) is standard with all Fuji T-Spray Guns. 1.0mm, 1.3mm or
1.5mm can be used for any type of fine-finishing application. The
larger sizes such as 1.5mm allow for more fluid output - desirable with
fast drying lacquers.
If you do not intend on spraying walls & ceilings the only addi-
tional Setups you need would be the 1.0mm, 1.5mm, and
1.8mm.
No. 1 (Part 5100-1) .8mm (.031") SUPER-FINE OUTPUT
SHADING, STAINS.
No. 2 (Part 5100-2) 1.0mm (.039") FINE OUTPUT
SHADING, STAINS, WATERBORNE COATINGS.
No. 3 (Part 5100-3) 1.3mm (.051") FINE - MEDIUM OUTPUT -
STANDARD
WATER-BASED LACQUERS, ACRYLICS, POLYURETHANE,
STAINS.
No. 4 (Part 5100-4) 1.5mm (.059") MEDIUM OUTPUT
Similar to No. 3 but more coverage. Best for AUTOMOTIVE
ENAMELS, LACQUER and LATEX for cabinetry and furniture. Also
VARNISHES, PRIMERS, OIL-BASED PAINTS.
No. 5 (Part 5100-5) 1.8mm (.070") HIGH OUTPUT
Larger surfaces, thick layers, spotted effects. SEALERS, VARNISH,
POLYURETHANE, OIL BASED PAINTS, ENAMELS, EPOXIES,
LATEX on walls, ceilings ETC.
No. 6 (Part 5100-6) 2.0mm (.078") EXTRA HIGH OUTPUT
Very heavy flows, fast coverage. STONE FINISH PAINTS, TEXTURE
COATING, INDUSTRIAL PRIMERS, MULTI-FLECK PAINTS, LATEX on
walls, ceilings ETC.
No. 7 (Part 5100-7) 2.5mm (.098") MAXIMUM HIGH OUTPUT
Heavy flows, faster coverage. LATEX HOUSE PAINT on walls etc.
AIR CAP SET - Part 5100 Series
PRESSURE POT USE FOR 4-STAGE OR 5-STAGE TURBINE
If you use a 4-stage Turbine or higher, a compressor is NOT needed to
pressurize the Fuji Spray 2 Qt. Pressure Pot.
The Fuji Spray 2 Qt. Pressure Pot Assembly 5432 has unique features.
These features combined with additional pressure from the Fuji Spray 4-
stage Turbine, allows the user to connect the larger capacity pot to the
Turbine system without the need for a compressor.
To connect the Fuji Spray 2Qt. Pressure Pot Assembly, remove the cup
assembly and the pressurizing tube 2024 from the spraygun.
Connect your material line (fluid hose) to the fluid coupler on the gun.
You must block off the air that would normally go from the gun to the cup
assembly. This nipple can be covered with Nipple Cap 5411.
PRESSURE POT USE FOR 3-STAGE
If you use a 3-stage Turbine or lower, a compressor IS NEEDED TO
PRESSURIZE THE POT.
PLEASE NOTE: The Fuji Spray 2 Qt. Pressure Pot Assembly 5432 has
been designed for Turbine use and is NOT compatible with a compressor.
However, you are able to hook up a standard 2Qt. Pressure Pot with a
compressor.
To connect to a Pressure Pot, remove the cup assembly and the
pressurizing tube 2024 from the spraygun.
Connect your material line (fluid hose) to the fluid coupler on the gun.
You must block off the air that would normally go from the gun to the cup
assembly. This nipple can be capped with Nipple Cap 5411.
If using a 2-stage or 3-stage Turbine, we recommend the use of a
compressor. Set the compressor to between 6-8 PSI. This is enough to
push the paint material up to the gun. For spraying at greater heights
(over 8 feet), more fluid pressure may be necessary. The fluid pressure
should never be set at more than 20 PSI. If you find a higher pressure is
needed, we advise you to check the material hose for paint blockage.
Loading ...
Loading ...
Loading ...