Loading ...
Loading ...
Loading ...
INALTO.HOUSE
PAGE 9
Installation
• Twopersoninstallation:Use two or more able-
bodied people to move and install the Beverage
Centre. Failure to do so can result in back or
other injury.
• Floorsurface:This Beverage Centre must be
properly positioned on a dry, sturdy, level surface
that is strong enough to support it when it is fully
loaded.
• Location:We recommend that this Beverage
Centre is installed in a sheltered location with the
required power safely accessible. For example: an
alfresco area, under a protected verandah or in a
garage. Please ensure it is not left in the weather
or in direct sunlight and it is always protected
from rain, water or excessive moisture.
• TropicalRating:This rating allows the Beverage
Centre to be operating eectively in temperatures
up to 43º C.
DoNOTinstall/usetheBeverageCentreinthe
followinglocations/situations:
• In a recreational vehicle, or for use with an
inverter.
• In direct sunlight, near heat sources, next to
an open ame, cooking or heating appliance,
or near any other source of high heat.
• Direct sunlight may aect the acrylic coating
and heat sources may increase the unit’s power
consumption. For best energy eciency install the
Beverage Centre in the coolest location within the
area it is placed.
• In an area with extreme cold ambient
temperatures.
• During camping.
• In an area with excessive moisture and high
humidity. Make sure it is protected from elements
such as wind, rain, water spray or drips.
• In an area where petrol or other explosive and/
or ammable liquids or fumes are used or stored.
The fumes can create a re hazard or explosion.
• Levelling:It is important for the Beverage Centre
to be level in order to work properly. To level the
unit, adjust the levelling legs at the bottom of the
Beverage Centre. See page 15 for more details
on this.
• Ventilation: To allow for proper air ventilation,
leave a minimum 5cm of space between the
back, sides and top of the Beverage Centre and
make sure that the front of the unit is completely
unobstructed.
• VentilationCont.:Ensure that the ventilation
openings are never blocked or covered. Never
cover shelves with aluminium foil or any other
material, which may prevent air circulation.
• Settling: Before connecting the Beverage
Centre to the power source, let it stand upright
for approximately 8 hours. This will allow any
refrigerant gasses that may have been disturbed
during the transportation process to settle and
reduce the possibility of a malfunction in the
cooling system from handling during transport.
• Electricalconnection: You should check
whether there is an electrical socket available,
which will be accessible after your appliance
is installed. Plug the Beverage Centre into a
dedicated, properly installed wall outlet. Do not
under any circumstances cut or remove the third
(earth) prong from the power cord. Any questions
concerning power and/or earthing should be
directed toward a licensed electrician or our after
sales support centre.
• After plugging the Beverage Centre in, turn the
unit on and allow it to cool down for 3–4 hours
before placing beverages in the appliance.
PositioningandAmbientTemperatures
• This Beverage Centre is rated to tropical ambient
temperatures. Your Beverage Centre may not
function correctly if the ambient temperature
exceeds 43º C.
• Your appliance should not be located in direct
sunlight or exposed to continuous heat or
extremes of temperature (e.g. next to a radiator
or boiler). If this is not feasible, then you should
install an insulation plate between the appliance
and the adjacent heat source.
• Place the Beverage Centre atly and rmly on a
solid base.
• Anything positioned above the Beverage Centre
must be at least 5 cm away to allow sucient
cooling of the condenser. You must allow a 5 cm
gap to the rear and either side of the appliance.
• Be sure to leave enough space for the opening of
the door, to avoid damage to the appliance or
personal injury.
Loading ...
Loading ...
Loading ...