Loading ...
Loading ...
Loading ...
INALTO.HOUSE
PAGE 15
CleaningandMaintenance
WARNING
Before cleaning the appliance, make sure it is
switched o and disconnected from the power
supply. Failure to do so can result in electric shock
or injury.
• Before cleaning: take out any drinks as well as the
shelves.
• Wash the inside surfaces with a solution of
lukewarm water (1L) and baking soda (2 tbsp).
Use a soft, clean cloth to wipe down the surfaces,
then rinse with clean water and dry with a dry
cloth. Do not use soap or detergent for cleaning
the cabinet. DO NOT allow the control panel,
cables or plug to get wet.
NOTE:Wring excess water out of the cloth when
cleaning around the controls or electrical parts.
• Make sure to keep the door gasket (seal) clean to
keep the unit running eciently.
• Wash the shelves and the outside of the cabinet
with a mild detergent solution.
Wipe dry with a clean soft cloth.
• Dust or anything else blocking the vent may
hinder the cooling eciency of the appliance.
Always keep the vent clean; vacuum it if
necessary.
WARNING
Never clean the unit with an abrasive, acid, oil or
solvent based cleaning agent. Never use ammable
uids or sprays for cleaning as the fumes from these
substances can create a re hazard or explosion.
WhenYouAreonHolidays
• Leave the Beverage Centre operating during
holidays of less than three weeks. If you are not
going to use the Beverage Centre for longer
periods, remove all items and unplug the power
cord. Clean and dry the interior thoroughly. To
prevent odours and mould growth, leave the door
open slightly, blocking it open
if necessary.
• To move the Beverage Centre, take all items out
of the appliance, securely tape down the shelves
or remove them and tape the door shut. Turn the
levelling leg up to the base to avoid damage.
• Protect the outside of the Beverage Centre with
a blanket or similar soft material and make sure
the Beverage Centre stays secure in the upright
position during transportation.
AdjustingtheHeightandLeveling
• The appliance is equipped with adjustable feet,
so that the height may be adjusted to level the
cabinet on uneven oor surfaces.
• We recommend that two people carry out this
procedure.
• The height must be adjusted prior to building
the appliance into the housing unit and it should
be set at such a height that the top panel of the
appliance ts 5cm below the kitchen worktop.
• Tilt the appliance approximately 60° to allow
access to the adjustable feet.
• Take care to ensure the cabinet is supported at all
times.
• Twist the foot into a suitable position to level the
cabinet. (Fig. 5)
• Repeat these steps for the other adjustable feet.
IMPORTANT: If the appliance is not level, then the
door and door seal may be aected.
IMPORTANT:Do not move the appliance when the
feet are adjusted high.
.17.
Adjusting the height and leveling off your wine cabinet
o The appliance is equipped with adjustable feet, so that the height may
be adjusted to level the cabinet on uneven oor surfaces.
o We recommend that two people carry out this procedure.
o The height must be adjusted prior to building the appliance into the
housing unit and it should be set at such a height that the top panel of
the appliance ts exactly below the kitchen worktop.
o Tilt the appliance approximately 60° to allow access
to the adjustable feet.
o Take care to ensure the cabinet is supported at all
times.
o Twist the foot into a suitable position to level the
cabinet.
o Repeat these steps for the other adjustable feet.
IMPORTANT: If the appliance is not level, then the door and door seal may
be affected.
IMPORTANT: Do not move the appliance when the feet are adjusted high.
Installing The Handle
o Remove the door Gasket slightly to
expose the two screw holes.
o Fix the Handle by screwing the two
Handle Screws tightly, the Handle
Screws with Washers are pre-installed
inside the screw holes, pls.do not
unscrew the Handle Screws too much
in case the Washers fell off.
o Replace the Gasket.
Fig. 5
Other Useful Information
Loading ...
Loading ...
Loading ...