1. Home
  2. Craftsman
  3. Craftsman CMECS614 User Manual
  4. Page 13

INSTRUCTION MANUAL - Page 13

For CMECS614.

Loading ...
Loading ...
Loading ...
11
English
WARNING: The use of accessories not recommended
in this manual may behazardous.
Replacement chain and bar are available from your nearest
CRAFTSMAN authorized service center. For use only with
low kick back bar andchain.
Available bars and chains for CMECs614:
Bar: service part number
CMZCSB14
Chain: service part number
CMZCSC14
Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with thisproduct.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN call 1-888-331-4569.
To get the best possible performance from your chain saw
it is important to keep the teeth of the saw chain sharp.
Follow these helpful tips for proper saw chain sharpening:
1. For best results use a 4.5mm file and a file holder or
filing guide to sharpen your saw chain. This will ensure
you always get the correct sharpeningangles.
2. Place the file holder flat on the top plate and depth
gauge of thecutter.
3. Fig.s- Keep the correct top plate
23
filing angle line of
30° on your file guide parallel with your chain (file at 60°
from chain viewed from the side).
4. Sharpen cutters on one side of the chain first. File from
the inside of each cutter to the outside. Then turn your
saw around and repeat the processes (2, 3, 4) for cutters
on the other side of thechain.
nOTE: Use a flat file to file the tops of the rakers (portion
of chain link in front of the cutter) so they are about
.025" (.635 mm) below the tips of the cutters as shown
in Fig.T.
5. Fig.U- Keep all cutter lengthsequal.
6. If damage is present on the chrome surface of the
top plates or side plates, file back until such damage
isremoved.
CAUTION: After filing, the cutter will be sharp, use
extra caution during thisprocess.
nOTE: Each time the chain is sharpened, it loses some of
the low kickback qualities and extra caution should be used.
It is recommended that a saw chain be sharpened no more
than fourtimes.
60°
Fig. S
23
.025"
(0.635mm)
Fig. T
Fig. U
Versatrack™ (Fig. V)
WARNING: To reduce the risk of
serious personal injury, turn unit off and
disconnect it from power source before making
any adjustments or removing/installing
attachments or accessories. An accidental start-up
can causeinjury.
WARNING: To reduce the risk of serious
personal injury, do not use a damaged Versatrack™
integral hang hook or Versatrack™ Trackwall. A
damaged Versatrack™ pegintegral hang hook or
Versatrack™ Trackwall will not support the weight of
thetool.
WARNING: To reduce the risk of serious
personal injury, DO NOT suspend tool overhead or
suspend objects from the pegintegral hang hook.
ONLY suspend tool on the Versatrack™ Trackwall using
the pegintegral hanghook.
WARNING: The Versatrack™ integral
hang hook is intended to mount the tool onto a
Versatrack™ Trackwall rail. Do not use the integral
hang hook to mount the tool to any othersurface.
WARNING: The Versatrack™ integral
hang hook is not a belthook.
WARNING: When hanging objects on a
Versatrack™ Trackwall rail, adequately space the tools
in order to not exceed 75 lb (35 kg) per linearfoot.
Loading ...
Loading ...
Loading ...