Loading ...
Loading ...
Loading ...
27
TRAEGERGRILLS.COM
The grease pan comes with a preinstalled 5-pack of
disposable aluminum liners. Replacement liner packs
are available for purchase at traegergrills.com. Empty
the grease pan as needed; frequency depends on the
amount of use.
3. CLEANING OUTSIDE SURFACES:
DANGER! Turn the Main Power switch OFF (O) and
disconnect the power cord.
Use a disposable rag or cloth dampened with warm,
soapy water to wipe the grease from the outside of the
grill. DO NOT use oven cleaner, abrasive cleansers, or
abrasive cleaning pads on the outside grill surfaces.
4. OUTSIDE STORAGE:
CAUTION! If the grill is stored outside during the rainy
season, care should be taken to ensure that water
does not get into the pellet hopper. Wood pellets
expand greatly when wet and will jam your auger.
Always cover your grill when not in use with the
Traeger grill cover. This custom-fit cover can be
purchased at traegergrills.com.
5. CLEANING THE STAINLESS STEEL GRILL GRATES:
CAUTION! Cleaning the grill grates works best while
they are still warm. Be careful not to burn yourself.
We recommend keeping a long-handled cleaning
brush near the grill. Afer removing your food,
give the grill grate a quick brushing. It takes only
a minute and it will be ready the next time you want
to use the grill.
6. CLEANING THE ASH FROM INSIDE AND AROUND
THE FIREPOT (EVERY 20 HOURS OF USE):
DANGER! Turn the Main Power switch OFF (O) and
disconnect the power cord.
WARNING! Make sure that the grill is COLD before
cleaning the ash.
WARNING! Disposal of ashes should be done only
according to the following instructions.
Excess ash in the firepot may cause your fire to go
out. The firepot should be inspected occasionally and
cleaned to remove the ash buildup. Again, cleaning the
ash from in and around the firepot should be done only
when the grill is COLD.
Remove the grill grates, grease drip tray, and heat
bae to provide access to the firepot and the interior
of the grill. Much of the ash outside of the firepot can
be removed from the grill with a small metal fireplace
shovel or other similar tool.
WARNING! A dedicated vacuum cleaner is the best
way to remove ashes from the firepot, but this must be
done with extreme care to avoid the risk of fire. Again,
cleaning the ash from the firepot should be done
only when the grill is COLD.
A utility-type vacuum cleaner having a metal collection
canister without a bag would be best for this task.
However, almost any vacuum cleaner will work safely
if this procedure is properly followed.
Afer ensuring that the ash in the firepot is COLD,
vacuum the ash from the inside of the firepot.
a. If your vacuum cleaner is a bagless model, empty
any previously accumulated debris from the
collection chamber. Then vacuum the ash from the
inside of the firepot. Once the firepot is clean, empty
the collection chamber into the metal container
described below without delay. Make sure that there
is no remaining ash residue lef in the collection
chamber.
b. If your vacuum cleaner is a model that uses a
disposable bag, install an unused bag in the
machine. Then vacuum the ash from the inside of
the firepot. Once the firepot is clean, remove the bag
from the vacuum cleaner and place it in the metal
container described below without delay.
7. DISPOSAL OF ASHES:
WARNING! Ashes should be placed in a metal
container with a tight-fitting lid. The closed container
of ashes should be placed on a noncombustible floor
or on the ground, well away from all combustible
materials, pending final disposal. When the ashes
are disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed
container until all cinders have cooled thoroughly.
8. CLEANING THE CUTTING BOARD:
Always thoroughly wash the cutting board afer use.
To wash:
(1) Hand-wash only in warm, soapy water.
DO NOT SOAK.
(2) Rinse with clean water.
(3) Air-dry.
IMPORTANT: Soaking the wooden cutting board in water
or washing it in the dishwasher can damage the board.
NOTE: Avoid overexposure to sunlight to prevent
warping.
9. If the supply cord is damaged, it must be replaced by a
special cord assembly available from the manufacturer
or its service agent.
Loading ...
Loading ...
Loading ...