Documents: Go to download!
User Manual
- User Manual - (English)
- User Guide - (English)
- Specification Sheet - (English)
- Product Documentation (PDF) - (English)
- IN THE BOX
- MACHINE SET UP
- BREWING ESPRESSO Using Pre-Ground Espresso
- BREWING ESPRESSO Using E.S.E. POD Espresso
- BREWING CAPPUCCINO or LATTE
- DELIVERING HOT WATER
- TEST YOUR WATER
- WATER FILTER
- CLEANING and MAINTENANCE: DESCAILING
- TROUBLESHOOTING
Table of contents
User Manual
IN THE BOX
MACHINE SET UP
Main switch on side of machine.
The machine preforms a self-test signalled by the sequential flashing of lights.
The machine is warming up, when lights stop blinking the machine is almost ready for use.
Fill water tank
Turn the steam dial to the position. The machine will prime and a little water will be released.
Turn the steam dial to the position. The machine is ready for use.
BREWING ESPRESSO Using Pre-Ground Espresso
Use correct filter, marked on bottom of cup.
Brew 1 or 2 Espresso at one time.
BREWING ESPRESSO Using E.S.E. POD Espresso
Use correct filter, marked on bottom of cup.
E.S.E. (which stands for Easy Serving Espresso) is the technology being used to simplify the preparation of a good espresso using just a few simple actions, thanks to the adoption of the “serving” (individual pre-packed doses containing 7 grams of ground coffee that has been pressed and hermetically sealed between two fine layers of filter paper).
BREWING CAPPUCCINO or LATTE
Refer to previous section BREWING ESPRESSO for the espresso related part.
Fill 1/3 of the pitcher, 3.5 oz. for Cappuccino, 6 oz. for Latte.
Be sure frother is immersed in milk, but not beyond the highlighted mark on the spout
Set the desired level of foam
If both coffee buttons are blinking, you must cool down the boiler.
Turn dial ON allowing water to be delivered. When water stops, turn dial to position.
Prepare the coffee as described in the previous sections. Brew in a larger cup.
Pour the milk over the espresso and enjoy!
DELIVERING HOT WATER
Delivering hot water
1. Place a container under the spout (as close as possible to avoid splashes).
2. Turn the steam dial to the position. Water runs out of the spout.
3. Turn the dial to the position when the desired amount of water has been delivered. NOTE: You can stop the flow of water by pressing the button. (You should not run off hot water for more than 2 minutes at a time).
4. Press any button.
Delivering steam
1. Make sure the hot water spout is attached correctly.
2. Fill a container with the liquid to be heated/ frothed and immerse the spout/ cappuccino maker in the liquid.
3. Press the button twice. After a few seconds, the steam to heat the liquid comes out of the cappuccino maker.
4. When the required temperature/foam is obtained, interrupt steam delivery by pressing the button again. (You should not discharge steam for more than 3 minutes at a time).
Tips for using steam to froth milk
- When choosing the size of the container, bear in mind that the liquid doubles or triples in volume.
- For a richer denser froth, use skimmed or partially skimmed milk at refrigerator temperature (about 41F/5°C).
- For a creamier froth, rotate the container with slow movements in an upward direction.
- To avoid milk with poor froth or large bubbles, always clean the spout.
TEST YOUR WATER
Measuring Water Hardness
1. Remove the “total hardness test” indicator paper attached to this manual from its pack.
2. Immerse the paper completely in a glass of water for one second.
3. Remove the paper from the water and shake lightly. After about a minute, 1,2,3, or 4 red squares form, depending on the hardness of the water. Each square corresponds to one level.
Press button and hold for 10 seconds. The lights will blink in sequence. You are now in the setting menu.
Press the button to enter the water hardness setting
Press the button that correspond to the correct hardness level.
The button indicates that the selection has been saved.
When setting the water hardness, it is very important to set the correct frequency of the descaling cycles. You should always keep this machine clean, and it will help improve its performance and prolong the life of the machine.
WATER FILTER
Installing the filter
- Remove the filter from packaging and rinse the filter with about half a liter of tap water.
- Rotate the calendar disk (A) so that the next two months are displayed.
- Remove the tank from the appliance and fill with water.
- Insert the filter(B) in the water tank and immerse it completely for ten or so seconds, sloping it to enable the air bubbles to escape.
- Insert the filter in the filter housing (C) and press as far as it will go.
- Close the tank with the lid (D), then replace the water tank in the machine.
- The new filter is active. You can now use the coffee maker
Please note! The filter lasts about two months if the appliance is used normally. If the coffee maker is left unused with the filter installed, it will last a maximum of three weeks
CLEANING and MAINTENANCE: DESCAILING
DESCALING
Descale the machine when the orange light comes on.
Important! Descaler contains acids which may irritate the skin and eyes. It is vital to respect the manufacturer’s safety warnings given on the descaler pack and the warnings relating to the procedure to follow in the event of contact with the skin and eyes.
NOTE: Failure to descale the appliance as described above voids the guarantee.
- Turn the machine on.
- Completely empty the water tank (A) and remove the water filter (if present).
- Pour the descaler (B) and water (C) into the tank, according to the manual instructions.
- Place an empty container (D) with a minimum capacity of 50 oz under the hot water spout and boiler outlet.
- Press the button and hold for 10 seconds. The lights will blink in sequence. You are now in the setting menu.
- Turn the steam dial to and press button. The descaling program automatically performs a series of deliveries at intervals to remove the lime scale from inside the coffee machine.
- From time to time turn the steam dial to the position to deliver small quantities of descaler from the boiler outlet.
- Once the descaling solution is terminated, the orange light starts blinking
- To eliminate the solution and lime scale residues, rinse the tank and fill it with fresh water (without descaler); empty the containers and place them under the boiler outlet and hot water spout.
- Turn the steam dial to the position and press the button to start the rinsing.
- From time to time turn the steam dial to the position to deliver small quantities of water from the boiler outlet
- Once the water tank is empty, turn the steam dial to position.
The appliance is now ready for use.
Repairs to the coffee machine relative to lime scale problems are not covered by the warranty if the descaling procedure described above is not performed on a regular basis.
Important!
- Descaler contains acids which may irritate the skin and eyes. It is vital to respect the manufacturer’s safety warnings given on the descaler pack and the warnings relating to the procedure to follow in the event of contact with the skin and eyes. Use De’Longhi descaler only. Under no circumstances should you use sulphamic or acetic based descalers. Their use invalidates the guarantee.
TROUBLESHOOTING
Problem | Cause | Solution |
No espresso coffee is delivered | No water in the tan | Fill the tank |
The holes in the filter holder are blocked | Clean the filter holder spout holes | |
The tank has been inserted incorrectly and the valves on the bottom are not open | Press the tank down lightly to open the valves on the bottom | |
Limescale in the water circuit | Descale as described in the section “Descaling” | |
The espresso coffee drips from the edges of the filter holder rather than the holes | The filter holder has been inserted incorrectly or is dirty | Attach the filter holder correctly and rotate firmly as far as it will go |
Attach the filter holder correctly and rotate | Have the espresso boiler gasket replaced by Customer Services | |
The holes in the filter holder spouts are blocked | Clean the spout holes | |
The filter holder cannot be attached to the appliance | Too much coffee has been placed in the filter | Use the measure supplied and make sure you are using the correct filter for the type of preparation |
The coffee froth is too light (delivered from the spout too fast) | The pre-ground coffee is not pressed down firmly enough | Press the pre-ground coffee more firmly |
There is not enough pre-ground coffee | Increase the quantity of pre-ground coffee | |
The pre-ground coffee is too coarse | Use only pre-ground coffee for espresso coffee makers | |
The wrong type of pre-ground coffee is being used | Change the type of pre-ground coffee | |
The coffee froth is too dark (delivered from the spout too slowly) | The pre-ground coffee is pressed down too firmly | Press the coffee down less firmly |
There is too much pre-ground coffee | Reduce the quantity of pre-ground coffee | |
The espresso boiler outlet is blocked | Clean as described in the section “Cleaning the boiler outlet” | |
The filter is blocked | Clean as described in the section “Cleaning the filter” | |
The pre-ground coffee is too fine | Use only pre-ground coffee for espresso coffee makers | |
The pre-ground coffee is too fine or damp | Use pre-ground coffee for espresso coffee makers only and make sure it is not too damp | |
Limescale in the water circuit | Descale as described in the section “Descaling” | |
After delivering coffee, the filter remains attached to the boiler outlet | Insert the filter holder again, deliver coffee, then remove the filter holder | |
The appliance will not make any drink and the and lights flash for a few seconds | No water in the tank | Fill the tank with water |
The tank has been inserted incorrectly and the valves on the bottom are not open | Press the tank down lightly to open the valves on the bottom | |
The espresso boiler outlet is blocked | Clean as described in the section “Cleaning the boiler outlet” | |
The filter is blocked | Clean as described in the section “Cleaning the filter | |
Limescale in the water circuit | Descale as described in the section “Descaling” | |
The appliance does not function and all the lights flash | With an extreme use, the appliance reaches a high temperature. Simply wait: the appliance will cool down automatically | |
The appliance does not function and all the lights flash for a long time | Abnormal machine conditions | Disconnect the appliance and contact authorised Customer Services. |
See other models: TRD40615T DE608M DEFV908R KBJ2001BCTJ2003BK EC860M