Loading ...
Loading ...
Loading ...
16
(if provided) with a damp cloth and a little mild washing
detergent;
2. Remove the lter (C4) (if present) and rinse with running
water;
3. Replace the lter (if provided), ll the tank with fresh
water and replace the tank;
4. (Models with water softener lter only) Deliver about 3.38
oz/100ml of water.
17.7 Cleaning the coee spouts
1. Clean the coee spouts (A19) regularly with a sponge or
cloth (g. 24A);
2. Check that the holes in the coee spouts are not blocked.
If necessary, remove coee deposits with a toothpick (g.
24B).
17.8 Cleaning the pre-ground coee funnel
Check regularly (about once a month) that the pre-ground
coee funnel (A4) is not blocked. If necessary, remove coee
deposits with the brush (C5).
17.9 Cleaning the infuser
The infuser (A8) must be cleaned at least once a month.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned o (see section
“5. Turning the machine o”);
2. Remove the water tank (A17);
3. Open the infuser door (A7) (g. 25) on the right side of the
machine;
4. Press the two coloured release buttons inwards and at the
same time pull the infuser outwards (g. 26);
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap;
Important!
RINSE WITH WATER ONLY
NO WASHING DETERGENT NOT DISHWASHER SAFE
Clean the infuser without using washing detergent as it
could be damaged.
6. Use the brush (C5) to remove any coee residues left in the
infuser housing, visible through the infuser door;
7. After cleaning, replace the infuser by sliding it onto the in-
ternal support, then push the PUSH symbol fully in until it
clicks into place;
Please note:
If the infuser is dicult to insert, before insertion, adapt it to the
right size by pressing the two levers (g. 27).
8. Once inserted, make sure the two coloured buttons have
snapped out;
9. Close the infuser door;
10. Put the water tank back.
18. DESCALING
Descale the machine when the light (B5) on the touch
screen (B) ashes and only the
OK (B15) and ESC
icons (B14) remain on.
To descale immediately, press
OK and follow the instruc-
tions from point 4.
To descale the machine later, press
ESC. The light
ashes on the touch screen to remind you that the machine
needs descaling.
Important!
• Before use, read the instructions and the labelling on the
descaler pack.
• You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may re-
sult in faults not covered by the manufacturer's guarantee.
To descale the machine, proceed as follows:
1. Turn the machine o (standby) by pressing the but-
ton (A24 - g. 7) (see section “5. Turning the machine o”);
2. Empty the drip tray (A15) and grounds container (A11) and
put both back in the machine;
3. Press and hold the icon (B8) until the light (B5)
and the ESC and OK icons light up;
4. Empty the water tank (A17) completely and remove the
water softener lter (C4), if present;
5. Pour the descaler (C3) into the tank up to level A (corre-
sponding to a 3.38 oz / 100ml pack) marked on the inner
surface of the tank, then add a litre of water up to level B
(g. 28) and put the water tank back in the machine;
6. Place a container with a minimum capacity of 1.8 litres
under the frother (A20) and coee spouts (A19) (g. 29);
Important! Danger of burns
Hot water containing acid ows from the frother and coee
spouts. Take care to avoid contact with splashes of this solution.
7. Press the OK icon to conrm that you have added
the descaler solution. The descaling procedure begins;
8. After a few minutes, the ESC icon (B14) ashes
to indicate the steam/hot water dial (A23) must be
turned to the I position;
9. When the dial has been turned to the l position, the des-
cale programme starts and the descaler liquid comes out
of the frother. A series of rinses and pauses are performed
Loading ...
Loading ...
Loading ...