Loading ...
Loading ...
Loading ...
82
Save Favorite Fill
Household water pressure may affect the accuracy of the
Favorite Fill feature. So, for optimum performance of your
water dispenser, you must first calibrate Measured Fill. (See the
“Calibrate Measured Fill” section).
NOTE: Water will not be dispensed using the Favorite Fill feature
unless your preferred Favorite Fill amount is saved first.
IMPORTANT:
■ Flush the water system before Favorite Fill.
■ For best results, calibration should be performed when water
is not being used in the house.
1. Place a preferred-size cup on the dispenser tray centered in
front of the ice/water dispenser paddle.
2. Select either Favorite Fill 1 or 2, and then touch and hold the
Favorite Fill button for 3 seconds to enter into Saving mode.
The Favorite Fill icon will illuminate and remain lit while the
Favorite Fill feature is being saved.
NOTE: You may touch the Favorite Fill button to exit at any
time in Saving mode and the display will return to the Home
screen.
3. Press and hold the water dispenser paddle, as needed, to
dispense water to the preferred-size cup.
NOTE: If overfilling or spilling occurs, discard the water and
restart the saving process.
4. When the preferred amount of water has been correctly
dispensed into the cup, touch the Favorite Fill button to
confirm the favorite amount.
5. When Favorite Fill amount has been confirmed, the display
will return to the home screen.
Dispensing
Touch the Cubed Ice or Crushed Ice button for your ice selection.
NOTES:
■ For crushed ice, cubes are crushed before being dispensed.
This may cause a slight delay when dispensing crushed ice.
Noise from the ice crusher is normal and pieces of ice may
vary in size.
■ When changing from crushed to cubed, a few ounces of
crushed ice will be dispensed along with the first cubes.
Dispensing Water
IMPORTANT:
■ Dispense at least 1 L (1 qt) of water every week to maintain a
fresh supply.
■ If the flow of water from the dispenser decreases, it could be
caused by low water pressure.
■ With the water filter removed, dispense 237 mL (1 cup) of
water. If 237 mL (1 cup) of water is dispensed in
8 seconds or less, the water pressure to the refrigerator
meets the minimum requirement.
■ If it takes longer than 8 seconds to dispense 237 mL
(1 cup) of water, the water pressure to the refrigerator
is lower than recommended. See the “Water Supply
Requirements” and “Troubleshooting” sections for
suggestions.
To Dispense Water — Standard:
1. Press a sturdy glass against the water dispenser paddle.
2. Remove the glass to stop dispensing.
NOTE: The Fill button (center button) does not enable standard
dispensing. It only functions in Measured Fill mode.
To Dispense Water — Measured Fill:
Measured Fill allows you to dispense a specified amount of water
with the touch of a few buttons.
1. Put a sturdy glass under waterspout. Touch the Measured Fill
button to activate.
NOTE: The amount of water you select will be dispensed.
Make sure the container can hold the entire volume. If ice
is in the container, you may need to adjust your selection.
2. Touch the Measured Fill button to turn on, then touch to
select 0.2 L (8 oz), 0.5 L (16 oz), or 0.7 L (24 oz). Touch a
fourth time to exit Measured Fill display.
3. Touch the Fill button or press paddle and the selected
amount of water will be dispensed.
NOTES:
■ The Measured Fill dispenser will automatically time out after
1 minute of inactivity.
■ You can refill several glasses with the same measurement
by continuing to touch the Fill button (center button) after
each glass fill.
Measured Fill options are listed in the following chart:
Units
Ounces 8 16 24
Cups 1 2 3
Liters 0,2 0,5 0,7
NOTE: Most coffee cups (commonly 118 to 177 mL [4 to 6 oz]
per cup) are not the same size as a measuring cup
(237 mL [8 oz]). You may need to recalibrate Measured Fill to
underfill or to avoid unintentionally overfilling coffee cups.
4. Dispense water.
NOTE: While dispensing water, the flow of water will
automatically stop once the desired volume has been
dispensed.
■ Press a sturdy glass against the dispenser paddle below
the waterspout.
OR
■ Place the glass below the waterspout and touch the Fill
button for hands-free dispensing.
5. To pause dispensing before the selected volume has been
dispensed, touch the Fill button a second time or touch the
water dispenser paddle. Touch the Fill button or paddle again
to resume dispensing remaining amount.
NOTE: If you stop dispensing before the desired volume has
been dispensed, the display will turn off after 1 minute. If you
have not resumed by then, it will reset back to the original
amount.
6. To select a new volume or start dispensing the same volume
again, you must first finish dispensing the selected volume or
turn off the Measured Fill feature (either by waiting 1 minute
so it will automatically turn off or by touching the Cubed Ice
or Crushed Ice button to manually turn it off), and then select
Measured Fill again.
To Dispense Water — Favorite Fill:
Favorite Fill allows you to dispense a preferred amount of water
with the touch of a few buttons.
1. Put a sturdy glass under waterspout. Touch the Favorite Fill
button to activate.
Loading ...
Loading ...
Loading ...