Loading ...
Loading ...
Loading ...
*5 (# '3
CONVERSIONE AD ALTRO
TIPO DI GAS
Prima della conversione ad
altro tipo di gas, accertatevi del
tipo per il quale l’apparecchio è
stato regolato. (etichetta
adesiva (Figura 1) applicata
sull’apparecchio).
Per il diametro dell’ugello
riferirsi alla tabella degli ugelli.
Sostituzione dell’ugello del
bruciatore inferiore
Rendere privo di tensione
l’apparecchio;
1) Estrarre la suola
copribruciatore (vedi
ESTRAZIONE DELLA
SUOLA pagina 42).
2) Svitare la vite di fissaggio
del bruciatore del forno ed
estrarre dal supporto
insieme all’elemento termico
e alla candela di
accensione. (Figura 5)
3) Togliere l’ugello dall’attacco
con una chiave a tubo da 7
(Figura 6)
4) Avvitare a fondo il nuovo
ugello (diametro impresso in
centesimi di millimetro
sull’ugello) facendo
attenzione all’inserimento
preciso del filetto.
5) Montare il bruciatore
procedendo in ordine
inverso rispetto a quanto
descritto al punto 2.
6) Reinserire la suola nella
7) Regolazione del minimo (vedi
istruzioni a pagina 16)
posizione giusta.
Fig. 5 - Abb. 5 - Afb. 5 Fig. 6 - Abb. 6 - Afb. 6
CONVERSION TO A
DIFFERENT TYPE OF GAS
Before converting the
appliance for operation with a
different gas type, check which
type of gas it is currently set to
operate with (adhesive label
(Figure 1) on appliance).
For the correct nozzle
diameter, refer to the relative
table in this booklet.
Disconnect the electrical
power supply to the appliance;
1) Remove the burner cover
Replacing the lower burner
nozzle
plate (
see REMOVAL OF
THE BURNER COVER
PLATE page 42).
2) Remove the screw securing
the oven burner and
withdraw the burner from
the support together with
the heat sensor and the
ignition spark plug. (Figure
5)
3) Remove the nozzle using a
7 mm box wrench (Figure 6)
4) Screw the new nozzle in
fully (diameter in hundredths
of millimetre stamped on the
nozzle), taking care not to
cross the thread.
5) Replace the burner
reversing the operations in
step 2 above.
6) Replace the cover plate.
7) Adjusting the minimum flame
(see instructions on page 16)
CONVERSION D
E TYPE DE
GAZ
Avant la conversion du gaz,
vérifier que le gaz actuel est
correctement réglé (étiquette
adhésive (Figure 1) appliquée
sur l’appareil).
Pour le diamètre du gicleur,
consulter la table des gicleurs.
Couper la tension;
1) Extraire la sole cache-
Remplacement du gicleur
du brûleur inférieur
brûleur (
voir EXTRACTION
sole page 42).
2) Dévisser la vis de fixation du
brûleur et extraire du
support avec l’élément
thermique et la bougie
d’allumage (Figure 5).
3) Retirer le gicleur de la
fixation avec une clé à
douille de 7 (Figure 6)
4) Visser à fond le nouveau
gicleur (diamètre en
centièmes de millimètres
sur le gicleur) en faisant
attention à l’insertion précise
du filetage.
5) Monter le brûleur en
procédant dans l’ordre
inverse du point 2.
6) Remettre en place la sole.
7) Réglage du minimum (voir
directives page 16)
12
Loading ...
Loading ...
Loading ...