Samsung DVE54M8750W/A3 Electric Dryer with Integrated Touch Controls

03 Dry Level

Press Dry Level to select a dry level from the options available. The corresponding indicator turns on.

• Larger or bulkier loads may require Very Dry or More Dry for complete dryness.
• Less Dry is best suited for lightweight fabrics or for leaving some moisture in the clothing at the end of the cycle.
• Damp Dry is designed to partially dry items. Use for items that lay flat or hang to dry.

NOTE

This option is not available with: STEAM SANITIZE, ACTIVE WEAR,

TIME DRY, QUICK DRY, AIR FLUFF, REFRESH, and WRINKLE AWAY.

04 Temp.

Press Temp. to change the temperature of the current cycle.

• High: For sturdy cottons or those labeled Tumble Dry.
• Medium: For permanent press, synthetics, lightweight cottons, or items labeled Tumble Dry Medium.
• Med Low: For heat lower than Medium. Use to dry synthetic or washable knit fabrics.
• Low: For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm.
• Extra Low: Provides the lowest heated drying temperature possible.

05 Time

Press Time to select a drying time for the selected cycle. This is available only with TIME DRY, QUICK DRY, AIR FLUFF, and WRINKLE AWAY.

06 Eco Dry

This function is available with NORMAL and TIME DRY.

With the Eco Dry activated, drying takes a longer time but the power consumption is reduced.

The drying time can be extended by up to 3 times depending on the temperature and load. The Eco Dry function is enabled by default.

07 Mixed Load Bell

The Mixed Load Bell notifies you when the average dry level in a load is damp dry (80 % dried). This lets you take items that you don’t want fully dried or that dry quickly out of the dryer early while letting others continue to dry.

You can select this option in all Sensor Dry cycle except for AIR

FLUFF, ACTIVE WEAR, TIME DRY, QUICK DRY, REFRESH, WRINKLE AWAY, and STEAM SANITIZE. Available dry levels are Normal Dry, More Dry, and Very Dry.

Reduces static electricity that occurs from clothing friction. This is done by spraying steam in a later stage of the drying cycle.

NOTE

The Anti Static function is only available with NORMAL, HEAVY DUTY, PERM PRESS, DELICATES, and TIME DRY.

Wrinkle Prevent provides approximately 180 minutes of intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling. Press Wrinkle Prevent to activate this feature. The load is dry and can be removed at any time during the Wrinkle Prevent cycle.

Choose your favorite cycle including the cycle time, temperature, and dry level. See “My Cycle” for details.

You can change the set time for the selected cycle. This is available only with TIME DRY, QUICK DRY, AIR FLUFF, and WRINKLE AWAY. To change the cycle time, press Adjust Time or Adjust Timeuntil the desired time is displayed.

12 Smart Control

(Elec.) /

Smart Monitor

(Gas)

After connecting the upper dryer to your home network using the Samsung Smart Home app, you can control the dryer remotely. When started, the Smart Control indicator blinks and the top door locks. The dryer enters waiting mode and waits for remote commands.

Press to turn on/turn off the dryer.

Press and hold to start operation, or press to stop operation.

Cycle

Description

NORMAL

For most fabrics including cottons and linens.

If NORMAL is selected, the Eco Dry function is enabled by default.

For more information, see Eco Dry in the “Feature panel“ section.

HEAVY DUTY

For drying items made out of heavy fabrics, such as jeans, corduroys, or work clothes, with high temperature heat.

PERM PRESS

Dry wrinkle-free cottons, synthetic fabrics, knits, and permanent press fabrics automatically.

BEDDING

For bulky items such as blankets, sheets, and comforters.

DELICATES

For heat-sensitive items at a low drying temperature.

ACTIVE WEAR

For exercise wear and outdoor wear such as sports jerseys, training pants, water-repellent jackets, and other performance clothing. Thick fabrics like a zipper or velcro closure of a jacket, or training socks may not be completely dried.

Cycle

Description

REFRESH

Use to smooth out wrinkles and reduce odors in loads of one to four items. With this cycle selected, a small amount of water is sprayed into the dryer drum after several minutes of tumbling with heat.

Confirm that the laundry load is dry.

WRINKLE AWAY

For best results, load 2-3 items at once. You can extend the drying time by a minimum of 20 minutes, depending on the item type or load. Confirm that the laundry load is dry.

STEAM SANITIZE

Use to sanitize items by applying steam and high-temperature heat to the fabric. This cycle can make items soft and reduce smells.

Confirm that the laundry load is wet or partially wet.

Cycle

Description

TIME DRY

You can specify a cycle time in minutes.

If TIME DRY is selected, the Eco Dry function is enabled by default.

For more information, see Eco Dry in the “Feature panel“ section.

QUICK DRY

A quick drying cycle running for 30 minutes

AIR FLUFF

Tumbles the load in room temperature air.

Cycle

Description

Bedspreads & Comforters

Follow the care label instructions or dry using BEDDING.

• Make sure the item is thoroughly dry before using or storing.
• May require repositioning in the drum to ensure even drying.

Blankets

Use NORMAL and dry only one blanket at a time for best tumbling action.

• Make sure blankets are is thoroughly dry before using or storing.

Curtains & Draperies

Use PERM PRESS and the Medium temperature setting to help minimize wrinkling.

• Dry curtains and draperies in small loads for best results and remove as soon as possible after the cycle is complete.

Cloth Diapers

Use NORMAL and the Medium temperature setting for soft, fluffy diapers.

Down–filled Items (jackets, sleeping bags, comforters, etc.)

Use NORMAL and the Medium temperature setting.

• Add a couple of dry towels to absorb moisture and shorten drying time.

Foam Rubber (rug backs, stuffed toys, shoulder pads, etc.)

Do not dry on a heat setting. Use AIR FLUFF.

WARNING

Drying a rubber item with heat may damage it or cause a fire.

Pillows

Use NORMAL.

• Add a couple of dry towels and a pair of clean sneakers to help the tumbling action and to fluff the pillows.
• Do not dry kapok or foam pillows using a heated drying cycle. You can dry these items in the dryer only if you use AIR FLUFF.

Plastics (shower curtains, outdoor furniture covers, etc.)

Use AIR FLUFF or TIME DRY and the Low or Extra Low temperature settings depending on the care label instructions.

Problem

Action

Does not run.

• Make sure the door is latched shut.
• Make sure the power cord is plugged into a live electrical outlet.
• Check your home’s circuit breakers or fuses.
• Press or tap START/PAUSE again if the door is opened during a cycle.
• Clean the lint filter.

Does not heat.

• Check your home’s circuit breakers or fuses.
• Some cycles do not require heating. Check the selected cycle again.
• For a gas dryer, make sure the gas supply is on.
• Clean the lint filter and exhaust duct.
• The dryer may have moved into the cool-down phase of the cycle.

Does not dry.

• Check all of the above, plus...
• Make sure the exhaust hood outside your home can open and close freely.
• Check the exhaust system for lint buildup. Ducting should be inspected and cleaned annually.
• Use a 4” rigid metal exhaust duct.
• Do not overload. 1 wash load = 1 dryer load.
• Dry heavy items and light weight items separately.
• Large, bulky items, such as blankets or comforters, may require repositioning to ensure even drying.
• Make sure that your washer is draining properly and extracting adequate water from the load.
• The load may be too small to tumble properly. Add a few towels and restart the dryer.
• The load may be too large to tumble properly. Remove some items and restart the dryer.
• Clean the lint filter.

Is noisy.

• Check the load for objects such as coins, loose buttons, nails, etc. Remove promptly.
• It is normal to hear the dryer gas valve or heating element cycle on and off during the drying cycle.
• Make sure the dryer is leveled properly as outlined in the installation instructions.
• It is normal for the dryer to hum due to the high velocity of air moving through the dryer drum, fan, or exhaust system.

Dries unevenly.

• Seams, pockets, and other similarly heavy areas may not be completely dry when the rest of the load has reached the selected dryness level. This is normal. You can choose a higher dryness level or a cycle that involves a higher dryness level.
• If one heavy item is dried with a light weight load, such as one towel with sheets, it is possible that the heavy item will not be completely dry when the rest of the load has reached the selected dryness level.
• For the best drying results, dry heavy items and light weight items separately.

Has odors.

• Household odors from paint, varnish, strong cleaners, etc. may enter the dryer with the surrounding room air. This is normal as the dryer draws the air from the room, heats it, pulls it through the tumbler, and exhausts it outside.
• When these odors linger in the air, completely ventilate the room before using the dryer.
• Use a cycle featuring the Refresh function. If odors persist, wash and dry the items again.

Lint on clothes.

• Make sure the lint filter is cleaned before every load. For clothes that naturally build up lint, clean the filter during the cycle.
• Some fabrics are lint producers (for example, a fuzzy white cotton towel) and they must be dried separately from clothes that are lint trappers (for example, a pair of black linen pants).
• Divide larger loads into smaller loads for drying.
• Check pockets thoroughly before drying, then dry clothes.
• Remove lint inside the drum before drying.

Code

Action

dC

Operating the dryer with the door open.

• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.

FC

Invalid power source frequency • Try restarting the cycle.

• If this information code remains, contact a Samsung service center.

AC

Electronic control problem (Invalid Communication).

• Contact a Samsung service center.

HC

High temperature heating check

• Clean the lint filter.
• If this information code remains, contact a Samsung service center.(enter the line test mode)

9C1

The electronic control needs to be checked.

• Check if power is supplied properly.
• If the information code remains, contact a Samsung service center.

tC

The Thermistor1 resistance is very low or high.

• Check for a clogged lint screen
• Check if the vent system is restricted.
• If this information code remains, contact a Samsung service center.

tC5

The Thermistor2 resistance is very low or high.

• Check for a clogged lint screen.
• Check if the vent system is restricted.
• If this information code remains, contact a Samsung service center.

dF

Incorrect door switch.

• Contact a Samsung service center.