Loading ...
Loading ...
Loading ...
16
Please note:
If “Energy saving” mode is active, there may be a few seconds
delay before steam is delivered.
Tips for using steam to froth milk
• When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
• For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C).
• For a creamier froth, rotate the container with slow move-
ments in an upward motion.
• To avoid milk with poor froth or large bubbles, always clean
the spout (C6) as described in the following paragraph.
Cleaning the hot water/steam spout after use
Always clean the hot water/steam spout (C6) after use to avoid
the build-up of milk residues and prevent it from clogging.
1. Place a container under the hot water/steam spout and let
a little water out (see section “Delivering hot water”). Then
stop the delivery of hot water by pressing .
2. Wait a few minutes for the hot water/steam spout to cool
down; then extract it (g.18). Hold the spout steady with
one hand and with the other, turn and detach the cappuc-
cino maker pulling it downwards (g.24).
3. Also remove the steam connection nozzle by pulling it
downwards (g.24).
4. Check the hole in the connection nozzle is not blocked. If
necessary, clean using a toothpick.
5. Wash all parts of the spout thoroughly with a sponge and
warm water.
6. Attach the connection nozzle and the cappuccino maker
onto the spout by pushing it upwards and turning it clock-
wise until it is secure.
CUSTOMISING BEVERAGES
The aroma (for drinks where required) and length of the drinks
can be customised.
1. Make sure that the prole for which customising the drink
is required is active: it is actually impossible to select the
drinks for all 6 proles ;
2. From the homepage, press (B1);
3. Choose the beverage you wish to customise in order to ac-
cess the customising screens: the relative accessories must
be inserted;
4. (Beverages with coee only) CHOOSE COFFEE AROMA LEV-
EL: Select the required aroma by pressing or
and press ;
5. CUSTOMISING COFFEE (OR WATER) QUANTITY, PRESS STOP
TO SAVE: Preparation begins and the appliance displays the
quantity customising screen in the form of a vertical bar.
The star alongside the bar represents the current quantity
set.
6. When the amount reaches the minimum quantity you can
set, the display shows .
7. Press when the required quantity in the cup is
reached.
8. SAVE NEW SETTINGS? : Press YES or NO.
The appliance conrms if the values have been saved or not (de-
pending on the previous selection): press .
The appliance goes back to the homepage.
Please note:
• Milk based drinks: the coee aroma is saved rst, followed
by the quantity of rst milk, then coee;
• Hot water: the appliance supplies hot water: press
to save the desired quantity.
• It is possible to come out of programming by pressing
: the values will not be saved.
MEMORISING YOUR PERSONAL PROFILE
The appliance allows you to memorise 6 dierent proles, each
associated with a dierent icon.
In every prole the customised beverages aroma and quantity
values are saved (see section “Customising beverages ”)
and the order in which all the beverages are displayed is based
on the frequency of selection.
To select or enter a prole, press on the prole currently in use
(B11), press (B10) or
(B8)
until the required prole is
displayed, then press on the prole.
Please note:
• Prole GUEST : select this prole to deliver beverages
with the default settings.
CLEANING
Cleaning the machine
The following parts of the machine must be cleaned regularly:
• appliance internal circuit;
• coee grounds container (A4);
• drip tray (A14);
• water tank (A12);
• coee spouts (A13);
• pre-ground coee funnel (A21);
• infuser (A5), accessible after opening the service door (A2);
• milk container (D);
• hot water/steam connection nozzle (A10);
• control panel (B).
Loading ...
Loading ...
Loading ...