Loading ...
Loading ...
Loading ...
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have nished.
39
holding the wok burner to the hotplate. Remove the 2 screws
and washers holding the right-hand tray to the frame.
Press the wok burner down slightly and, taking care not to
damage the wok burner electrode, slide the tray about 30 mm
to right to clear the locating brackets on the right-hand side.
Lift tray slightly at the front and taking care not to stress the
warmer/lead junction, disconnect the leads to the warmer
neon and separate the leads at the piggybacks. Withdraw the
hotplate.
Reassemble in the reverse order ensuring that the leads are
reconnected. When replacing the right-hand hotplate take
care not to damage the ignition electrode of the wok burner.
It is important that the rear xing screws are retted as they
from part of the cooker earthing.
On some models there is a separate plate (Fig. 10.1). On
others it is a tag on the cooker backsheet (Fig. 10.2).
It is important that the tag is on the outside and that both
xing screws are tted.
Check for correct burner operation.
2.2 To Replace the Hotplate Control Taps
DISCONNECT FROM THE ELECTRICITY SUPPLY.
BEFORE SERVICING ANY GAS CARRYING
COMPONENTS, TURN OFF THE GAS SUPPLY.
Remove the control panel and hotplate (see 1.1 & 2.1). Unplug
the FSD lead from the rear of the tap. Undo the compression
tting at the rear of the tap and remove the xings that secure
the tap to the gas rail. Disconnect the ignition switch wiring.
Remove the tap. Remove and discard the gasket seal. Fit
the new gasket seal to the replacement tap. Reassemble in
reverse order. Check that the appliance is gas sound. Verify the
hotplate ignition.
2.3 To Change a Hotplate Burner Injector
Remove the burner cap and head. Remove the old injector.
Fit the new injector. Reassemble in the reverse order. Check
the appliance is gas sound.
2.4 To Replace a Hotplate Burner Electrode
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Lift o pan supports and remove the burner cap. Remove the
screw holding the electrode. Pull the electrode vertically up
suciently to grip the lead between thumb and forenger.
Pull o the electrode, but keep hold of the lead. Fit the new
electrode to the lead. Fix the electrode in the burner with
screw. Replace the burner cap.
Check the burner ignition. Replace the pan supports.
2.5 To Replace a Hotplate Burner
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the hotplate tray (see 2.1). The burners (except the
right-hand wok burner) are mounted on support struts. For
these burners, disconnect the burner feed pipes at the burner.
Remove the screws at the front and rear holding the support
struts. Lift the strut and burners clear. The burners are xed
to the support struts with 2 screws. Remove the appropriate
burner and t the new one.
Reassemble in reverse order. Check that the burner operation
is satisfactory.
Right-hand Wok Burner
Disconnect the burner feed pipes at the burner.
Fit the new one and reassemble in reverse order. Check that
the burner operation is satisfactory.
2.6 To Change a Hotplate Burner Thermocouple
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel and hotplate (see 1.1 & 2.1).
Unplug the FSD lead from the rear of the tap.
The thermocouple sits in a hole that has a slot at one side.
Ensure that the thermocouple is cool. Turn the thermocouple
so that the earth lead (no sleeve) is in line with the slot. Lift the
thermocouple clear of the hole.
Reassemble in reverse order.
2.7 To Change the Warmer Neon
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove right-hand hotplate (see 2.1). Carefully turn the
hotplate upside down on a suitable at surface. Remove the
2 screws holding neon bracket to warmer frame. Fit the new
neon and bracket assembly.
Reassemble in reverse order and check for correct operation.
2.8 To Change the Warmer
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the right-hand hotplate (see 2.1). Fit the new right-
hand hotplate and reassemble in reverse order.
Check the burner and warmer operation is satisfactory.
3 Controls
3.1. To Replace the Ignition or Light Switch
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel (see 1.1).
Note: The old switch may be destroyed during removal.
Remove the old switch from its bezel by gripping the switch
body behind the control panel and twisting sharply. Remove
the switch bezel by folding back the locking wings and
pushing forward.
To t the new bezel to the control panel: rst line up the raised
key on its body with the cut-out in the control panel and push
it in from the front.
Assemble the new switch to the bezel by lining up the key
sections and pushing home. Fit the new button by pushing in
from the front.
Replace the control panel in the reverse order and test for
correct operation.
Loading ...
Loading ...
Loading ...