Loading ...
Loading ...
Loading ...
7
This washer is heavy. Two or more people are required when
moving and unpacking the washer. Failure to do so may
result in damage to property or serious bodily harm.
conditions. Failure to follow this warning can cause serious
injury, re, electric shock, or death.
Properly ground the washer to conform with all electric
governing codes and ordinances. Failure to follow this
warning can cause serious injury, re, electric shock, or death.
in humid spaces. Failure to follow this warning can cause
serious injury, re, electric shock, or death.
Do not remove ground prong. Do not use an adapter or
extension cord. Plug into a grounded 3-prong outlet. Failure
to follow this warning can cause serious injury, re, electric
shock, or death.
• Certain internal parts are intentionally not grounded and may
present a risk of electric shock only during servicing. Service
personnel - Do not contact the following parts while the
appliance is energized: pump, valve, motor, control board.
NOTE: Installing the washer in a humid space, or installing or
storing the washer where it will be exposed to the weather or
freezing temperatures, may result in rust or other damage that is
not covered by the product warranty.
Power Outlet
• The power outlet must be within 60 in. (1.5 m) of either
side of the washer.
• The appliance and outlet must be positioned so that
the plug is easily accessible.
• Do not overload the outlet with more than one appliance.
• The outlet must be grounded in accordance with
current wiring electric codes and regulations.
• Time-delay fuse or circuit breaker is recommended.
NOTE: It is the personal responsibility and obligation of
the product owner to have a proper outlet installed by a
qualied service technician.
• To minimize noise and vibration, the washer MUST be
installed on a solidly constructed oor. See the NOTE at right.
• Allowable slope under the entire washer is a maximum
1 in. dierence from side to side or from front to back.
• Installing on carpeting and soft tile surfaces is not
recommended.
• Never install the washer on a platform or weakly
supported structure.
NOTE: The oor must be strong and rigid enough to
support the weight of the washer, when fully loaded,
without exing or bouncing. If your oor has too much ex,
reinforce it to make it more rigid.
A oor that is adequate for a top-loading washer may
not be rigid enough for a front loading washer, due to the
dierence in the spin speed and direction. If the oor is not
solid, your washer may vibrate and you may hear and feel
the vibration throughout your house.
Description Front-Loading Washer
Electrical Requirements 120 VAC, 60 Hz
Max. Water Pressure 20 - 120 psi (138 - 827 kPa)
Dimensions 27”(W) X 30 ¼”(D) X 39”(H), 55” (D with door open)
70 cm(W) X 77 cm(D) X 99 cm(H), 139.6 cm (D with door open)
Net Weight 187.4 lbs (85 kg)
Max. Spin Speed 1,300 RPM
WARNING
To ensure sucient clearance for water lines and airow,
allow minimum clearances of at least 1 in. (2.5 cm) at the
sides and 4 in. (10 cm) behind the unit. Be sure to allow
for wall, door, or oor moldings that may increase the
required clearances.
Allow at least 24
3
/4 in. (62.6 cm) in front of the washer
to open the door.
4 in.
(10 cm)
24
3
/
4
in.
(62.6 cm)
31
1
/
4
in.
(77 cm)
55
in.
(139.6 cm)
INSTALLATION REQUIREMENTS
1 in.
(2.5 cm)
1 in.
(2.5 cm)
27 in.
(70 cm)
KEY DIMENSIONS AND SPECIFICATIONS
CHOOSE THE PROPER LOCATION
FLOORING
CLEARANCES
Loading ...
Loading ...
Loading ...