User Manual Bissell 2852 MultiClean Allergen Lift-Off Pet Vacuum

• Owner's manual - (English)

Table of contents

• Product Overview
• What’s in the Box?
• Assembly
• Using Your Vacuum
• Above Floor Cleaning
• Emptying the Dirt Tank
• Cleaning the Inner Cyclone Separator
• Cleaning and Replacing the Filters
• Protecting the Vacuum’s Motor
• Troubleshooting

User Manual vacuum cleaner

Product Overview

1. Carpet Type Control

2. Hose

3. Quick Release Extension Wand

4. Dirt Tank Release Button

5. Power Switch

6. Brush Roll Switch

7. Pre-Motor Filter

8. Dirt Tank

9. Lift-Off Release Button

10.Post-Motor

What’s in the Box?

Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton top flap.

Lift-Off Pod

Handle

Stretch Hose

Foot

2-in-1 Dusting Brush & Crevice Tool

Pet TurboEraser® Tool

Assembly

1. Attach Handle to Lift-Off Pod.

2. Attach Lift-Off Pod to Foot

3. Attach Stretch Hose to Handle by twisting clockwise.

4. Attach Stretch Hose to back of vacuum by twisting clockwise.

5. Attach tools to tool holders on vacuum.

Using Your Vacuum

1. Turn power ON. Turn the Brush Roll ON for carpet cleaning and the light switch will illuminate. Turn the Brush Roll OFF when vacuuming hard or delicate surfaces

2. Step gently on base and pull the handle back to recline. Note: The Brush Roll automatically shuts OFF when vacuum is locked in upright position. Recline to reactivate.

3. Use the Carpet Type Control for optimized cleaning on high pile and low pile carpet. The control can be moved to the middle position for medium pile carpeting.

Above Floor Cleaning

1. Push the Lift-Off Release Button and lift up to remove the pod from the Foot.

2. For the most reach, use the Quick Release Extension Wand. Push the Release Button to remove. To clean without the the wand, twist circular hose cuff counter-clockwise and remove.

3. Attach desired tool. Note: For optimal use, attach the Pet TurboEraser® Tool directly to the Hose instead of the Handle.

4. Use the Carry Handle to bring the Lift-Off Pod to hardto-clean places in your home.

5. Replace the wand back by sliding into place until you hear a “click”. Reattach Hose to Handle if needed.

6. Place the pod back onto the Foot.

Emptying the Dirt Tank

1. Press the Dirt Tank Release Button and grab the handle to pull the Dirt Tank away from vacuum.

2. Hold the Dirt Tank over a trash bin and press the Empty Button. Once emptied, snap bottom back into place.

3. Return the Dirt Tank to the vacuum by securing the bottom in place first and then pushing back until you hear a “click”.

Cleaning the Inner Cyclone Separator

1. Hold the Dirt Tank over a trash container. Press the bottom release button to empty

2. Twist separator counterclockwise and pull down to remove.

3. Tap separator against inside of trash container and rinse under warm water, if necessary. Be sure to let it dry completely before placing back in Dirt Tank.

Cleaning and Replacing the Filters

1. Press the Dirt Tank Release Button and pull away from vacuum.

2. Open the tank lid by lifting up

3. Remove Pre-Motor Filters from top of Dirt Tank lid by pulling out.

4. Clean with mild detergent, rinse and squeeze all excess water. Allow filters to dry completely before reinserting.

5. Return Pre-Motor Filters to the top of the Dirt Tank. Put the thin flat filter with the white tab in first, then put the thick foam filter in.

6. You should hear a click when tank lid is closed securely

Post-Motor Filter

For optimal performance, replace the filter every 6 months.

1. Press down on tab to remove Post-Motor Filter cover and pull away from vacuum.

2. Press tab on right side of filter and pull out to remove from vacuum. Remove debris from filter by tapping on the side of a trash container. This pleated filter may NOT be washed.

3. When reassembling, be sure to lock the filter back into place by aligning one side of the filter first, then clicking the other side into place.

Protecting the Vacuum’s Motor

There is an internal thermal protector in your vacuum that protects it from overheating. It controls the main vacuum motor only, not the brush motor. When it activates, the main motor will stop. The front lights and Brush Roll will stay on but there won’t be any suction. If this happens, follow these steps:

1. Turn vacuum OFF and unplug from electrical outlet.

2. Check for the source of overheating problem (full Dirt Tank, dirty filters or a clog) and fix by following the steps in the “Vacuum won’t pick up dirt” troubleshooting section.

3. When the motor cools for approximately 30 minutes, the thermal protector automatically resets and cleaning may continue. If the vacuum will not turn ON or the thermal protector continues to activate contact Consumer Care.

Troubleshooting