Loading ...
Loading ...
Loading ...
4
Before Using For the First Time
Do not position this appliance with its rear panel directly against a wall. For good ci
operating efficiency, the ventilation grilles must never be blocked.
Remove all packaging and place the
BeefEater Fridge
away from heat sources, where the unit is well
moisture, or extremes of heat or cold. The refrigerator may not function properly if the
temperature rises above +40
for prolonged periods of time.
When installed in a BeefEater Outdoor Kitchen, ensure the vents behind the fridg
clean, and not obstructed from the other side, such that air circulation is enabled.
Do Not Use An Extension Lead
rearrange your installation
layout or ask a qualified electrici
If power is cut off, wait for at least 5 minutes before plugging the unit in again to avoid damaging
the compressor.
Do not place combustible,
explosive
containers into the
BeefEater Fridge
Preparation
Position the Shelf-
Supports inside the racks on the sides as illustrated below, at your required level,
and then p
lace the shelves firmly on the supports.
The maximum load for a shelf is 40Kg.
Cleaning
1.
Unplug your BeefEater Fridge from power source and remove any items from inside. It is best to
place these temporarily in another refrigerator.
2.
Wash the inner compartment with warm water and neutr
control panel, cables or plug to get wet.
NEVER use corrosive detergents, wire blasters, or abrasive scourers to clean your
BeefEater Fridge.
NEVER use metal or sharp implements to scrape any part of the fridge.
3. Dry all surface thoroughly.
4. To ensure trouble-
free operation the condenser should be cleaned every three months where
appropriate using a vacuum hose. The condenser is located behind lower grill of the cabinet. In
exceptionally dusty
It is recommended that areas
5.
Use mild soapy water to clean the gasket and seals around the door.
6.
The external surfaces of the fridge can be cleaned with warm water and mild detergent, or with
a suitable Stainless-
Steel cleaning material.
IMPORTANT: allow the refrigerator to stand
upright for 8 hours before
Before Using For the First Time
Do not position this appliance with its rear panel directly against a wall. For good ci
operating efficiency, the ventilation grilles must never be blocked.
Remove all packaging and place the
BeefEater Fridge
on a stable, secure flat surface. Position the
away from heat sources, where the unit is well
-
ventilated
moisture, or extremes of heat or cold. The refrigerator may not function properly if the
for prolonged periods of time.
When installed in a BeefEater Outdoor Kitchen, ensure the vents behind the fridg
clean, and not obstructed from the other side, such that air circulation is enabled.
Do Not Use An Extension Lead. If the mains cable will not reach the nearest socket, either
layout or ask a qualified electrician to fit a new socket.
If power is cut off, wait for at least 5 minutes before plugging the unit in again to avoid damaging
explosive
or volatile articles, corrosive acid or alkali, or liquid in glass
BeefEater Fridge. Always exercise caution if adjusting the temperature.
Supports inside the racks on the sides as illustrated below, at your required level,
lace the shelves firmly on the supports.
The maximum load for a shelf is 40Kg.
Unplug your BeefEater Fridge from power source and remove any items from inside. It is best to
place these temporarily in another refrigerator.
Wash the inner compartment with warm water and neutral mild detergent. DO NOT allow the
control panel, cables or plug to get wet.
NEVER use corrosive detergents, wire blasters, or abrasive scourers to clean your
NEVER use metal or sharp implements to scrape any part of the fridge.
free operation the condenser should be cleaned every three months where
appropriate using a vacuum hose. The condenser is located behind lower grill of the cabinet. In
It is recommended that areas
around the condenser are cleaned more often.
Use mild soapy water to clean the gasket and seals around the door.
The external surfaces of the fridge can be cleaned with warm water and mild detergent, or with
Steel cleaning material.
IMPORTANT: allow the refrigerator to stand still and
upright for 8 hours before
plugging it in
to the power!
Note
: check that the refrigerator
is functioning correctly before
installing shelves and filling it.
Do not position this appliance with its rear panel directly against a wall. For good ci
rculation and
on a stable, secure flat surface. Position the
ventilated
and protected from
moisture, or extremes of heat or cold. The refrigerator may not function properly if the
ambient
When installed in a BeefEater Outdoor Kitchen, ensure the vents behind the fridg
e are clear, and
clean, and not obstructed from the other side, such that air circulation is enabled.
. If the mains cable will not reach the nearest socket, either
an to fit a new socket.
If power is cut off, wait for at least 5 minutes before plugging the unit in again to avoid damaging
or volatile articles, corrosive acid or alkali, or liquid in glass
. Always exercise caution if adjusting the temperature.
Supports inside the racks on the sides as illustrated below, at your required level,
Unplug your BeefEater Fridge from power source and remove any items from inside. It is best to
al mild detergent. DO NOT allow the
NEVER use corrosive detergents, wire blasters, or abrasive scourers to clean your
NEVER use metal or sharp implements to scrape any part of the fridge.
free operation the condenser should be cleaned every three months where
appropriate using a vacuum hose. The condenser is located behind lower grill of the cabinet. In
around the condenser are cleaned more often.
The external surfaces of the fridge can be cleaned with warm water and mild detergent, or with
still and
to the power!
: check that the refrigerator
is functioning correctly before
installing shelves and filling it.
Loading ...
Loading ...
Loading ...