Loading ...
Loading ...
Loading ...
7
:9>@80=$@;;:=?%=:@-70>3::?492%4;>!;0=,?4929>?=@.?4:9>$,10?D9>?=@.?4:9>
;;74,9.0>.:8
!;?4:9>
#0-41/0<)*7>-<0-;-4-+<-,8),?144*-! <716,1+)<-?01+078<1760);*--6;-4-+<-,
STEAM For use with heavily soiled and/or dried-on, baked-on soils. This option &$%be selected "#!#
to starting the cycle. #0-$%78<176),,;516=<-;<7<0-+A+4-<15-
HEATED DRY Shuts off the drying heat option. Dishes air dry naturally and energy is saved. For faster air dry,
1/0< you can prop the door open after the light illuminates.
HEATED DRY Turns the heater on for faster drying. This will extend the total cycle time between
1/0< 8 and 38 minutes depending on the cycle selected. !%%#*cannot be
selected with # $! *cycle.
LOCK (7=+)647+3<0-+76<:74;<78:->-6<)6A;-4-+<176;.:75*-16/5),-:A7=+)647+3<0-+76<:74;
).<-:A7=0)>-;<):<-,)+A+4-
014,:-6+)667<)++1,-6<)44A;<):<,1;0?);0-:*A<7=+016/8),;?1<0<01;78<176;-4-+<-,
To LOCK the dishwasher control, touch and hold the %#* pad for 3 seconds. The light
below the %#* pad will turn on. To UNLOCK the dishwasher control, touch and hold the
%#* pad for 3 seconds. The ! light will turn off.
ADDED When selected, the cycle will run longer with the heating element on to improve both wash and
HEAT dry performance. !% Cannot be selected with # $! *cycle.
DELAY HOURS You can delay the start of a wash cycle for up to 9 hours. Touch the *!&#$ pad to choose
the number of hours you want to delay the start of the cycle; then touch $%#%#$%one time.
The dishwasher will count down and start automatically at the correct time. Touching
$%#%#$% a second time will cancel the *$%#% selection.
RESET To change a cycle after washing starts, touch the $%#%#$% pad to cancel the cycle. For some
models, the $%#%#$% light will flash while the water is pumped out. This takes approximately
90 seconds. The door must be closed to complete pump out. When the light stops flashing, the
dishwasher can be reprogrammed and restarted. Buttons will not respond during pump out.
For other models, the $%#%#$% will turn off and the drain pump will pump water out of
the dishwasher for 90 seconds and then turn off. Cycle selection and option ’s will remain on,
and buttons will respond during pump out. If the $%#%#$% is pressed while the dishwasher is
in pump out, the $%#%#$% will turn on and the dishwasher will start a new wash cycle
$?,=? Close and latch the dishwasher door and select the cycle and desired enhancements. Touch the
$%#%#$% pad once to begin the cycle. Water begins to fill the dishwasher, and approximately
60 seconds later the wash action begins.
!%The dishwasher remembers your last cycle so you don’t have to reprogram each time.
When the dishwasher door is fully closed, the control panel lights will display the last settings you
selected.
If you don’t want to change any of the settings, simply touch the $%#%#$%pad once to begin
the cycle.
If the door is closed, the indicator lights will turn off if the $%#%#$% pad is not pressed within
two minutes.
To activate the display, open and close the door or touch any pad.
Also, if a power failure occurs, !#($and %#*will automatically be
programmed.
Loading ...
Loading ...
Loading ...