Loading ...
Loading ...
Loading ...
10
Level Range
1. Place a rack in oven.
2. Place level on rack and check levelness of range, first side to
side, then front to back.
3. If range is not level, pull range forward until rear leveling leg
is removed from the anti-tip bracket.
4. Use a wrench or pliers to adjust leveling legs up or down
until the range is level. Push range back into position.
5. Check that rear leveling leg is engaged in the anti-tip
bracket.
NOTE: Range must be level for satisfactory baking performance.
Electronic Ignition System
Initial lighting and gas flame adjustments
Cooktop and oven burners use pilotless igniters in place of
standing pilots. When the cooktop control knob is turned to the
Lite position, the system creates a spark to light the burner. This
sparking continues, as long as the control knob is turned to Lite.
When the oven control is turned to the desired setting, a glow
bar igniter heats and ignites the gas.
Check Operation of Cooktop Burners
Standard Surface Burners
Push in and turn each control knob to the Lite position. The
flame should light within 4 seconds. The first time a burner is lit
it may take longer than 4 seconds to light because of air in the
gas line.
If burners do not light properly:
■ Turn cooktop control knob to the Off position.
■ Check that the range is plugged in and the circuit breaker as
not tripped or the household fuse has not blown.
■ Check that the gas shut-off valve is set to the “open”
position.
■ Check that burner caps are properly positioned on burner
bases.
Repeat start-up. If a burner does not light at this point, turn the
control knobs to OFF and contact your dealer or authorized
service company for assistance.
Adjust Flame Height
Adjust the height of top burner flames. The cooktop LO burner
flame should be a steady blue flame approximately
1
/
4
" (0.64 cm)
high.
To adjust standard burners:
The flame can be adjusted using the adjustment screw in the
center of the valve stem. The valve stem is located directly
underneath the control knob.
If the low flame needs to be adjusted:
1. Light 1 burner and turn to lowest setting.
2. Remove the control knob.
Hold the knob stem in the low position using a pair of pliers.
Use a
1
/
8
" (3.0 mm) flat-blade screwdriver to turn the screw
located in the center of the control knob stem until the flame
is the proper size.
3. Replace the control knob.
4. Test the flame by turning the control from LO to HI, checking
the flame at each setting.
5. Repeat steps 1 - 4 for each burner.
Check Operation of Both Oven Bake Burners
1. Press the Bake keypad for the desired oven.
“BAKE” scrolls down in the upper text display area or
scrolls up in the lower text display area, depending on oven
selection, and 350°F is displayed. After 3 seconds “Set
temp” scrolls in the selected oven text display area, followed
by “Push START.”
2. Press Start pad. “Baking” scrolls in the selected oven text
display area. Then, after 3 seconds, “Preheating” scrolls in
the display.
The igniter used to light the bake burner will glow. Once
the igniter is hot, the oven bake burner should light. Under
certain conditions, it may take up to 60 seconds for it
to light.
If burners do not light properly:
■ Press OFF/CANCEL to turn off the oven.
■ Check that the range is plugged in and circuit breaker has
not tripped or the household fuse has not blown.
■ Check that the gas shut-off valve is set to the open position.
Repeat start-up. If burner does not light, press OFF/CANCEL to
turn off the oven and contact your dealer or authorized service
company for assistance.
A
B
A. Low flame
B. High flame
Loading ...
Loading ...
Loading ...