Loading ...
Loading ...
Loading ...
19 201-877-646-5288 ninjakitchen.com
ENGLISH
CARE &
MAINTENANCE
CLEANING
1 Separate all parts.
2 Hand Washing
Wash containers, lids, blade assemblies
and Blade Discs in warm, soapy water
using a dishwashing utensil with a handle or
the provided cleaning brush to avoid direct
contact with the blades. Exercise care
when handling blade assemblies, as the
blades are sharp. Thoroughly rinse and
air-dry all parts.
Dishwasher
All attachments are dishwasher safe. It is
recommended that the lids, containers, blade
assemblies, and Blade Discs be placed on
the top rack of the dishwasher
ONLY
. Ensure
that blade assemblies and Blade Discs are
removed from their containers before placing
in the dishwasher. Exercise care when
handling blade assemblies.
3 Wipe the motor base with a clean, damp
cloth. Allow to dry completely before
operation.
STORING
Wrap the power cord around the back of the
motor base. Store the unit upright and store
all blade assemblies inside or attached to their
respective containers with their lids locked in
place.
DO NOT
stack items on top of the containers.
Store any remaining attachments alongside
the unit or in a cabinet where they will not be
damaged or create a hazard.
RESETTING THE MOTOR THERMOSTAT
This unit features a unique safety system
that prevents damage to the motor and drive
system should you inadvertently overload the
unit. If the unit is overloaded, the motor will be
temporarily disabled. Should this occur, follow
the reset procedure below.
1 Unplug the unit from the electricaloutlet.
2 Allow the unit to cool for approximately 15
minutes.
3
Remove the container lid and blade assembly.
Empty the container and ensure no ingredients
are jamming the blade assemblies.
4 Reset the unit in accordance with the
applicable instructions for the container
and blade type.
IMPORTANT: Ensure that maximum
capacities are not exceeded. This is the
most typical cause of unit overload.
If your unit needs servicing, please call
Customer Service at 1-877-646-5288.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments,
please visit ninjakitchen.com or contact
customer service at 1-877-646-5288.
TROUBLESHOOTING
GUIDE
WARNING: To reduce the risk of shock and unintended operation, turn
power o and unplug unit before troubleshooting�
Unit doesn’t turn on�
• Make sure unit is plugged in.
• Insert and rotate container clockwise on base until it clicks. Programs will illuminate, indicating your unit is
ready for use.
Unit doesn’t turn o�
• Remove container from base by rotating it counterclockwise and lifting it up. Display should turn off. Unplug
the power cord from the outlet.
Ingredients are not evenly chopped�
• For best results when chopping, cut pieces down to even sizes and do no overfill the Precision Processor
™
Bowl.
Motor base won’t stick to counter or tabletop�
• Make sure surface and suction feet are wiped clean. Suction feet will only stick to smooth surfaces.
• Suction feet
will not
stick on some surfaces such as wood, tile, and non-polished finishes.
•
DO NOT
attempt to use appliance when the motor base is stuck to a surface that is not secure (cutting
board, platter, plate, etc.).
Unit is dicult to remove from counter for storage�
• The suction feet at the base of the unit provide stability when in use. To release suction, gently pull the unit
toward you.
You get semi-circular or shredded noodles�
• If the Collecting Bowl is overfilled, causing the Blade Disc to lift up after Spiralizing, your ingredient may have
been too large. Make sure to trim and prepare your ingredients properly before spiralizing by following the
instructions in the Food Prep section of your Quick Start Guide or Inspiration Guide.
• For the most consistent results, be sure to center the ingredient on the pin located in the center of the Blade
Disc. (Refer to page 15, step 2.)
Ingredient is not fully processed and is spinning on the pusher�
• Remove remaining ingredient from Blade Disc pin and trim top and bottom so that both are flat. Make
sure you center ingredient on the Blade Disc pin and secure the Food Pusher firmly on top of the
ingredient. While maintaining pressure on Food Pusher, press the START/STOP button.
Unit turned o while in use�
• As a safety feature to prevent damage to the motor and drive system, the unit will power off after a
continuous run of 45 seconds.
Loading ...
Loading ...
Loading ...