Loading ...
Loading ...
Loading ...
9
Powders and Gels
Water
Hardness
Soil Level Prewash
Compartment*
Main Wash
Compartment
Soft
(0-4 grains
per U.S.
gallon)
Light None “Soft” fill line
Normal None “Soft” fill line
Heavy Full “Soft” fill line
Medium
(5-9 grains
per U.S.
gallon)
Light None “Soft” fill line
Normal Full Full**
Heavy Full Full**
Hard
(10-14 grains
per U.S.
gallon)
Light Full Full**
Normal Full Full**
Heavy Full Full**
*The prewash compartment is on top of the sliding door of
the dispenser.
**A full main wash compartment contains 2 Tbsp (30 ml).
IMPORTANT: Extremely hard water mineral deposits (15 grains
per U.S. gallon or more) can cause damage to your dishwasher
and make it difficult to achieve good results. A water softener is
recommended to avoid damage and achieve good results.
NOTE: Follow instructions on the package when using other
dishwasher detergent types.
STEP 3
Rinse Aid
SLIDE
IMPORTANT: Your dishwasher is designed to use rinse aid. The
use of rinse aids greatly improves drying by allowing water to
drain from the dishes after the final rinse. Rinse aid also keeps
water from forming droplets that can dry as spots or streaks.
Filling the dispenser
Full
Ad
d
The dispenser holds 5 oz (150 mL) of rinse
aid. Under most conditions this will last
1 to 3 months.
NOTE: Indicator reads correct fill level
when door is completely opened.
1.
Pre
Wash
OPEN
SLIDE
To add rinse aid, open the
rinse dispenser lid by gently
pushing in the center of the lid
with your thumb and pulling
up on the edge.
2. Pour rinse aid into the
opening until the dispenser
is full. Do not overfill.
3. Clean up any spilled rinse aid.
Spilled rinse aid can create excessive suds.
4. Then, close the dispenser by pushing down
gently on the lid.
Rinse Aid Setting
Your rinse aid dispenser is adjustable. For most
water conditions, the factory setting will give
good results. If you have hard water and notice
calcium buildup on your dishware, you may want
to try a higher setting. If you notice foam in your
dishwasher, use a lower setting.
To adjust the setting:
Turn the arrow adjuster to a higher number
to increase the amount of rinse aid.
STEP 4
Select a Cycle
Efficient dishwashers run longer to save water and energy, just
as driving a car slower saves gas. Cycle times may increase or
decrease depending on selections. Estimated cycle times after
calibration are listed in the “Cycle and Option Descriptions”
chart in the following section. Select the desired cycle by
pressing the Cycles button. Each time you press the Cycles
button, it will advance to the next available cycle.
Select Options
See the “Cycle and Option Descriptions” chart in the
following section.
You can customize the cycles by pressing the options
desired and pressing Start/Resume.
STEP 5
Start or Resume a Cycle
■ If needed, run hot water at the sink nearest your dishwasher
until the water is hot. Turn off water.
■ For best dishwashing results, water should be 120ºF (49ºC)
as it enters the dishwasher.
■ Select the wash cycle and options desired.
To repeat the same cycle and options used
previously, press START/RESUME twice.
Within 4 seconds of pressing Start/Resume
you must firmly push the door closed. If the
door is not closed within 4 seconds, the
Start button LED will flash, an audible tone
will be heard, and the cycle will not start.
■ You can add an item at the beginning of the cycle. Open the
door slowly and add the item. Press START/RESUME and
close the door firmly within 4 seconds. If the door has been
open more than 4 seconds the LED will flash, a tone will
sound and the dishwasher will not resume unless you press
Start/Resume again.
IMPORTANT: If the door has been opened after starting a cycle
(even during the Delay Hours option), Start/Resume must be
pressed again.
Loading ...
Loading ...
Loading ...