Loading ...
Loading ...
Loading ...
8 49-5903-3
INSTALLATION OF SINK FLANGE
(Read completely before starting.)
Correctly Installed Sink Flange
(shown for proper orientation)
INSTALLATION INSTRUCTIONS
COMPONENTS AND INSTALLATION
Installation Instructions
COMPONENTS
Rubber Gasket
6LQN)ODQJH
Support
Ring
)LEHU
Gasket
Groove
Bottom
Bead
Sink
)ODQJH
Cushion
Mount
Mount Ring should be
free to move up and down
Open Area
No Obstruction
Bottom Bead of
Cushion Mount
Sink
NOTE:3D\FORVHDWWHQWLRQWRWKHRUGHURIWKHVLQN
flange parts, as they have been correctly assembled
by the factory.
A.'LVDVVHPEOHWKHVLQNIODQJHDVVHPEO\IURPWKH
disposer by turning the mount ring to the left
(clockwise) and removing it.
B. Raise the mount ring toward the top of the sink
flange. Remove the cushion mount and the mount
ring. You may want to practice installing the
cushion mount at this point before you are under
the sink.
C.8QVFUHZWKHVXSSRUWULQJIURPWKHVLQNIODQJHDQG
remove the fiber gasket. You are now left with the
sink flange and the rubber gasket.
D. The rubber gasket is used instead of plumbers
putty with stainless steel sinks. Some cast iron
sinks will require putty.
E. If no putty is used, insert the sink flange through
WKHUXEEHUJDVNHWLQWRWKHVLQNRSHQLQJ'RQRW
turn the flange once it is seated.
F. If you use putty instead of the gasket, form a ring
around the underside of the sink flange. Insert the
flange into the sink opening, press down hard to
VTXHH]HRXWH[FHVVSXWW\)RUXQGHUWKHVLQNWULP
off excess putty flush with the bottom edge of the
sink opening.
G.)URPXQGHUQHDWKWKHVLQN
slip the fiber gasket onto the
exposed sink flange. With
arrows pointing up, screw
the support ring onto the sink
flange and hand-tighten until
the sink flange will not move.
At this point you may want to insert the stopper in
the sink and fill with water to check the sink flange
seal and insure there are no leaks.
H.3ODFHWKHPRXQWULQJRYHU
the sink flange and hold
in place while installing
the cushion mount (large
side down). Make sure the
groove on the inside of the
cushion mount fits over the
lip on the sink flange, similar
to putting the lid on a plastic
container. Run your fingers
around the entire cushion
mount with slight pressure.
'RQRWSUHVVWRRKDUG:KHQ
the cushion mount is properly
seated, the mount ring can be pulled downward
over the cushion mount and will be free to turn.
Hand-tighten sink flange
7RSGroove
Bottom Bead
Cushion Mount Detail
*Stopper
*Removable
Splash Guard
6LQN)ODQJH
)LEHU*DVNHW
Mounting Ring
Elbow Gasket
Hopper
Groove
Screws
Elbow
)ODQJH
Rating Label
in this Area
End Bell
(Electrical
Connections)
'LVKZDVKHU
'LVFKDUJH,QOHW
7LJKWHQLQJ
Ears
Cushion
Mount
Support Ring
(Note Arrows
,QGLFDWLQJ8S
Sink
Rubber Sink
)ODQJH*DVNHW
Sink
)ODQJH
Assembly
'LVSRVHU
'LVFKDUJH
Elbow
*Not used with batch feed model
Loading ...
Loading ...
Loading ...