User Manual Vremi 50 x 60 inches Electric Throw Heated Blanket

• Owner's manual - (English)

Table of contents

• Parts List
• Operating Instructions
• Troubleshooting
• Cleaning & Maintenance
• Important Safety Instructions
• Warranty Information

User Manual Blanket

Parts List

1. Electric Blanket
2. Blanket Connector
3. Control Connector
4. Control Panel
5. Power Cord

Operating Instructions

Before each use, always inspect the product to ensure there is no damage to the Power Cord, the Control Panel and the Blanket.

WARNING:

1. The Blanket Connector and Control Connector are designed to connect only one way. Align the inner prongs and then push together until Connectors are fully inserted (Fig. 1).

2. Plug the product into a 120V AC electrical outlet.

NOTE: If there is no power, make sure the AC electrical outlet is functional and the connection in step 1 is secure. Discontinue use if failure continues.

3. Use the Control Panel to set the heat to desired level.

NOTE: Heat levels are “85” (low), “85-110” and “110” (high).

4. Press the On/Off Button on the Control Panel. The display will illuminate and all icons will display. As a default, “85°F” will display, indicating the Control is set at the lowest heat level. “4h” will display, indicating the Control Panel is set at the 4 hours auto off.

WARNING: Burns may occur even if you set the temperature at low level. Check your skin under the Blanket frequently.

5. To change your desired heat level, press the “+” Button for a higher heat level or the “-” Button for a lower heat level. You can set it within 3 seconds after turning on and “SET“ will appear for about 3 seconds, and then display the real-time temperature of the pad.

Display Of Heat Level Settings:

as Level 6

as Level 3

NOTE: If the Control Panel shuts off, make sure the Blanket and Control connectors are securely connected and re-start the product by pressing the On/Off Button.

6. Place the Blanket on top of the body. If the Blanket does not heat evenly, make sure there are no folded areas.

7. Turn the product off by pressing the On/Off Button. Unplug it when not in use.

Auto Off Function:

This product will turn off after a set duration of time. You can set it at 0.5 hour (30 minutes), 1.0 hours, 1.5 hours (90 minutes), 2.0 hours (120 minutes), 2.5 hours (150 minutes), 3.0 hours (180 minutes), 3.5 hours (210 minutes) and 4.0 hours (240 minutes).

1. After turning the Blanket on and selecting the desired heat setting, press the “ ” Button until the desired amount of time is displayed. Time display will flash for 3 seconds, and then the desired time setting will display steadily.

NOTE: When the Electric Blanket is turned off, the default Auto Off is 4.0 hours (240min). 2. Repeat the above step to change the Auto Off setting.

WARNING: THE CONTROL CONNECTOR CANNOT BE COVERED WHEN USING.

Troubleshooting

Cleaning & Maintenance

WASHING INSTRUCTIONS

WARNING: NEVER DRY CLEAN OR USE BLEACH.

BEFORE WASHING, DISCONNECT ALL CORDS.

Machine Wash:

NEVER submerge cords or control unit. Place textile portion without cords in the washing machine. Machine wash warm on gentle or delicate cycle.

Hand Wash:

Washing your warming product by hand is the best way to make it last. To do this, disconnect all cord(s). Wash your textile separately by hand in a tub of lukewarm (100°F) water using a small amount of mild laundry soap or detergent. Soak for 5 minutes. Next, gently work the textile up and down for five more minutes. NEVER rub or scrub. Rinse thoroughly in cool water until all traces of soap or detergent are gone. Squeeze excess water out by hand, NEVER twist.

Do not use a wringer.

DRYING INSTRUCTIONS

WARNING: NEVER USE COMMERCIAL DRYERS AT THE LAUNDROMAT. THEY MAY BE EXTRA HOT AND COULD DAMAGE THE WIRING. DO NOT IRON. DO NOT PLUG IN UNTIL COMPLETELY DRY.

Machine Dry:

To machine dry, put your product into a dryer on low heat and allow to tumble until dry. Ensure that the textile has enough room to tumble freely. If product draws in during washing, while still damp gently stretch until it returns to its original size.

Line Dry:

You can line dry, simply by draping over two parallel clotheslines or a shower rod with the head and foot ends down. Do not reconnect warming products until they are completely dry. Do not use clothes pins that can pinch wires.

Storage:

Store as you would any other bedding, folded in a dry place.

FREQUENTLY ASKED QUESTIONS

1. When should an Electric Blanket be used?

Whenever a hot form of temporary relief is desired for personal comfort.

2. What temperature does this product reach?

Maximum temperature should not exceed the laboratory test limit of 149°F when set to Level 6. Temperature varies by heat setting. You may need to use a lower heat setting depending on the specific application and your personal preference.

3. How much time does it take to heat up to each temperature selection?

Temperature Selection Indicator Heat Up Elapsed Time Low 15 min

Important Safety Instructions

DANGER: To reduce risks of burns, electric shock, fire, and personal injury, this product must be used in accordance with the following instructions:

Setting Up:

1. NEVER trap or pinch any of the electrical cords in any way. Make sure the cords are NEVER rested between the mattress and box springs.
2. The heated area should always lie flat to prevent overheating.
3. If the plug does not fit into your outlet, contact a qualified electrician.
4. Be sure that the power supply is used only on 120V, 60 HZ current supply.
5. Make sure the cord from the controller to your heated product is connected and locked tightly.
6. You may use this electric product with any sheets, mattress pads or other blankets but NEVER in combination with any other electric blankets or electric mattress pads.
7. The warming product should never be folded, balled up or bunched in any way when in use. May result in overheating and/or permanent wrinkling of the fabric.
8. Do not use with generators, power converters, or inverters.

Care and Maintenance:

1. NEVER use pins in and around the warming product.
2. Cats, dogs and other pets should always be kept away from the product, as a sharp claw may result in damage to the heating element.
3. Always turn off the electric current when the warming product is not in use, either by turning off the controller or unplugging from the wall outlet.
4. Wrapping of the cord around the controls may damage the cord. Loop loosely when storing. 5. NEVER iron your warming product.
5. NEVER use dry cleaning fluid on this product. Cleaning solvents may damage the wiring insulation.
6. Do not tuck in the wired area of this bedding.
7. Do not route electrical cords between the mattress and box spring.
8. Do not allow the cords to be pinched.
9. Keep the control away from drafty areas that may become damp or wet such as an open window.
10. Do not use pins – They may damage the electric wiring.
11. Be sure that this bedding is used on an alternating-current supply circuit of the proper voltage.
12. Turn off or unplug when not in use. Excessive heating may result from folding bedding, other than a mattress, when in actual use.
13. If improper operation of this bedding is observed, discontinue its use immediately and consult the manufacturer or the dealer regarding its repair.
14. For throw blankets only: Do not use with rocking chairs, recliners, chairs with casters or wheels, or other furniture subject to movement.
15. Do not tuck the blanket or supply cord in a sofa or other furniture. All portions of the blanket or controller should be visible at all times.

This Electric Blanket has a polarized plug (one blade is wider than the other) as a safety feature. This plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.

DO NOT ATTEMPT TO DEFEAT THIS SAFETY FEATURE.

Warranty Information

Vremi offers a 12-month warranty on all of our products purchased new and unused from Vremi LLC or an authorized reseller, with an original proof of purchase and where a defect has arisen, wholly or substantially, as a result of faulty manufacturing, parts or workmanship during the Warranty Period. The warranty does not apply where damage is caused by other factors, including but without limitation: (a) normal wear and tear; (b) abuse, mishandling, accident or failure to follow operating instructions; (c) exposure to liquid or infiltration of foreign particles; (d) servicing or modification of the product other than by Vremi. These are our general terms for the warranty service, but we always urge our customers to reach out to us with any issue, regardless of warranty terms. If you experience an issue with a Vremi product, please contact us at support@vremi and we will do our best to resolve it for you.

This product complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This product may not cause harmful interference and

(2) This product must accept any interference received,including interference that may cause undesired operations.