Loading ...
Loading ...
Loading ...
Version 07/11 - Page 9
• This rangehood uses 20 watt, G4 Bi - Pin halogen lamps.
FOR ALL INSTALLATIONS
Rangehood Control Panel and Hood Operation
The control panel is located on the front edge of the rangehood
canopy. The position and function of each control button are
indicated in FIGURE 13.
Cleaning
hot detergent solution or washed in the dishwasher. Stainless
steel cleaner should be used on stainless rangehoods.
Abrasives and scouring agents can scratch stainless steel
FIGURE 12
2. Turn the power supply on. Turn on blower and lights. If the
rangehood does not operate, check that the circuit breaker is not
tripped or the house fuse blown. If the unit still does not operate,
disconnect the power supply and check that the wiring connec-
tions have been made properly.
WIRING DIAGRAM
FIGURE 13
USE AND CARE INFORMATION
This rangehood system is designed to remove smoke, cooking
vapors and odors from the cooktop area.
For Best Results
Start the rangehood several minutes before cooking to develop proper
complete to clear all smoke and odors from the kitchen.
Replacing the Lamps
levering it from under the metal ring, supporting it with one hand.
Remove the halogen lamp from the lamp holder by pulling gently.
Replace the lamp with a new one of the same type, making
sure that you insert the two pins properly into the housings on
the lamp holder. Replace the snap-on lamp cover.
FIGURE 16
1.
(FIGURE 12)
are properly positioned with the handles in front and visible.
0 1 2 3 4 5 6 7 8 9
Creato da.
Rev :
Ver :
DOLCE CORRADO
Materiali: non deveno contenere Pb, Cr6+, Hg, PBB, pbde, ai sensi della direttiva 2002/95 CE
SCHEMA ELETTRICO M8-4V ATL FARETTI
Non rilevare quote dal grafico non app ortare modifiche senza l'autorizzazione d'ufficio progettazione
a termini di legge ci riserviamo la propr ieta' del presente disegno con divieto di riprod uzione totale o parziale
Code :
Disegno N :
Data:
11.Nov.2010
436005191
H90_065
CN13
CN9
CN12
CN4
CN7
CN1
FASE
NEUTRO
COM
V1
V2
V3
V4
LUC.1 F.LUC.1 F.
LUC.1 N.
LUC.2 F.
LUC.2 N.
LINE IN
120Vac
60Hz ~
L
N
Y-G
WIRING BOX
Y-G
Faber ATL
1
2
3
4
5
7
6
1
2
3
4
BLU
BLK
L-B
RED
BLU
PNK
GRY
BRW
BLK
1
1
BLK
123
6 5 4
789
1 2 3
654
987
RED
M8 4V
120V ~
WHT
2
2
WHT
WHT
BRW
BRW
3
3
BRW
BLU
GRY
4
4
GRY
BLK
BLU
5
5
BLU
ORG
RED
6
6
RED
PNK
7
7
PNK
Y-G
VLT(ORG)
8
8
VLT(ORG)
RED(ORG)
9
9
RED(ORG)
RED
10
10
RED
VLT
11
11
VLT
12
12
TOROIDAL
TRANSFORMER
WHT
4
3
BLK
VLT
RED
2
1
BLK
RED
HALOGEN
LAMPS
ORG
2
1
ORG
4
3
RED
VLT
HALOGEN
LAMPS
HALOGEN
LAMPS
ORG
ORG
RED
HALOGEN
LAMPS
VLT
PRI.
SEC.
ELECTRONIC
TRNSFORMER
A
B
C
D
E
Button A.
Button B. Press to reduce fan speed to as low as speed
seconds to turn on 30 minute delay feature which runs the
hood for 30 minutes and automatically shuts the hood off.
a blinking light to indicate 30 minute mode. Shut off the 30
minute mode by holding down the button for 3 seconds
Button C. LED single digit readout display screen
Button D. Press button to increase fan speed up to speed 3.
Hold for 3 seconds to activate intensive speed mode which
operates hood on highest speed for 10 minutes and then
speed with an "H" and blinking light. Shut off the intensive
speed mode by holding down the button for 3 seconds
Button E. Press the button to turn on and off lighting. Press
once to turn the dimmer light on, press twice to turn the normal
light setting on, and press again to turn off the lighting.
Loading ...
Loading ...
Loading ...