Loading ...
Loading ...
Loading ...
4 Push the on/off slide downwards to
switch off the shaver.
5 Clean the shaver after every shave, see
chapter ‘Cleaning and maintenance’.
6 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 8).
Cleaning and maintenance
Never use scouring pads, abrasive cleaning
agents or aggressive liquids such as petrol or
acetone to clean the appliance.
Clean the shaver after every shave to
guarantee better shaving performance.
For the best cleaning result, we advise you to
use Philips Cleaning Spray (HQ110). Ask your
Philips dealer for information.
Note: Philips Shaving Head Cleaning Spray
(HQ110) may not be available in all countries.
Contact the Customer Care Centre in your
country about the availability of this accessory.
After every shave: shaving unit and
hair chamber
1 Switch off the shaver.
2 Clean the top of the appliance with the
cleaning brush supplied (Fig. 9).
3 Press the release button (1) and pull the
shaving unit a straight up off the shaver
(2) (Fig. 10).
4 Clean the inside of the shaving unit with
the cleaning brush (Fig. 11).
5 Clean the hair chamber with the cleaning
brush (Fig. 12).
6 Put the shaving unit back onto the
shaver (Fig. 13).
Every two months: shaving heads
Note: Do not use cleaning agents or alcohol
to clean the shaving heads. Only use Philips
Cleaning Spray (HQ110).
1 Switch off the shaver.
2 Press the release button (1) and pull the
shaving unit straight up off the shaver
(2) (Fig. 10).
3 To remove the retaining frame, push the
sides of the central spring towards each
other (1). Then lift the retaining frame
out of the shaving unit (2) (Fig. 14).
4 Slide the shaving heads out of the
retaining frame. Remove and clean one
shaving head at a time. Each shaving head
consists of a cutter and a guard (Fig. 15).
Note: Do not clean more than one cutter and
guard at a time, since they are all matching sets.
If you accidentally mix up the cutters and guards,
it may take several weeks before optimal shaving
performance is restored.
5 Remove the guard from the
cutter (Fig. 16).
6 Clean it with the short-bristled side of
the cleaning brush. Brush carefully in the
direction of the arrows (Fig. 17).
7 Clean the guard with the long-bristled
side of the cleaning brush (Fig. 18)
8 Put the cutter back into the guard after
cleaning (Fig. 19).
9 Slide the shaving heads back into the
retaining frame. (Fig. 20)
10 Put the retaining frame back into the
shaving unit (‘click’) (Fig. 21).
11 Put the shaving unit back onto the
shaver (Fig. 13).
storage
Keep the appliance dry.
Use and store the appliance at a temperature
between 5°C and 35°C.
1 Switch off the shaver.
2 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 22).
Replacement
Replace the shaving heads every two years for
optimal shaving results.
Replace damaged or worn shaving heads with
Philips shaving heads only (HQ4+ for China or
HQ56 for the rest of the world).
For instructions on how to remove the shaving
heads, see chapter ‘Cleaning and maintenance’,
section ‘Every two months: shaving heads’.
Accessories
To retain the top performance of your shaver,
make sure you clean it regularly and replace its
shaving heads at the recommended time.
shaving heads
- We advise you to replace your shaving
heads every two years. Always replace
them with Philips shaving heads only
(HQ4+ for China or HQ56 for the rest
of the world) (Fig. 23).
Cleaning
- Use Philips Cleaning Spray (HQ110) to
clean the shaving heads thoroughly.
Environment
- Do not throw away the appliance
with the normal household waste at
the end of its life, but hand it in at an
ofcial collection point for recycling.
By doing this, you help to preserve the
environment (Fig. 24).
- Batteries contain substances that may
pollute the environment. Do not throw
away batteries with the normal household
waste, but dispose of them at an ofcial
collection point for batteries. Always
remove the batteries before you discard
and hand in the appliance at an ofcial
collection point (Fig. 25).
guarantee and service
If you need service or information or if you
have a problem, please visit the Philips website
at www.philips.com or contact the Philips
Consumer Care Centre in your country.
You nd its phone number in the worldwide
guarantee leaet. If there is no Consumer Care
Centre in your country, go to your local
Philips dealer.
guarantee restrictions
The shaving heads (cutters and guards) are
not covered by the terms of the international
guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the
appliance. If you are unable to solve the
problem with the information below, contact
the Consumer Care Centre in your country.
Problem Possible cause Solution
The
shaver
does
not
shave as
well as it
used to.
The shaving
heads are dirty.
You have not
cleaned the
shaver well
enough or
you have not
cleaned it for a
long time.
Clean the
shaver thor-
oughly before
you continue
shaving. See
chapter
‘Cleaning and
maintenance’.
Long hairs
obstruct the
shaving heads.
Clean the
cutters and
guards with
the clean-
ing brush
supplied.
See chapter
‘Cleaning and
maintenance’,
section ‘Every
two months:
shaving heads’.
Problem Possible cause Solution
The shaving
heads are dam-
aged or worn.
Replace the
shaving heads.
See chapter
‘Replacement’.
The
shaver
does
not
work
when I
push the
on/off
slide up-
wards.
The batteries
are placed
incorrectly.
Make sure
the + and -
indications on
the batteries
match the
indications in
the battery
compartment.
The batter-
ies are empty.
Replace the
batteries.
See chapter
‘Preparing for
use’.
My
skin is
irritated
after
shaving.
Your skin needs
time to get
used to the
Philips shaving
system.
Skin irritation
during the
rst 2-3 weeks
of use is possi-
ble. After this
period, the
skin irritation
usually disap-
pears.
The
rotation
speed
of the
shaving
heads is
slower
than
usual.
Too much dirt
has collected
in the shaving
heads.
Clean the
shaving heads.
See chapter
‘Cleaning and
maintenance’.
The batteries
are empty
Replace the
batteries.
See chapter
‘Preparing for
use’.
The ap-
pliance
makes a
strange
noise.
Too much dirt
has collected
in the shaving
heads.
Clean the
shaving heads.
After cleaning,
lubricate
the central
point on the
inside of the
guards with
Philips Clean-
ing Spray
(HQ110).
See chapter
‘Cleaning and
maintenance’.
Problem Possible cause Solution
The shaving
heads are dam-
aged or worn.
Replace the
shaving heads.
See chapter
‘Replacement’.
DEUTsCh
Einführung
Herzlichen Glückwunsch zu Ihrem Kauf
und willkommen bei Philips! Um das
Kundendienstangebot von Philips vollständig
nutzen zu können, sollten Sie Ihr Produkt unter
www.philips.com/welcome registrieren.
Allgemeine Beschreibung (Abb. 1)
1 Schutzkappe
2 Scherköpfe
3 Schereinheit
4 Scherkopfhalter
5 Mittlere Feder des Scherkopfhalters
6 Entriegelungstaste
7 Haarauffangkammer
8 Ein-/Ausschalter
9 Batteriefachabdeckung
10 Philips Reinigungsspray (HQ 110)
(Optional)
11 Schneideeinheit
12 Schutzkappe
13 Reinigungsbürste
Wichtig
Lesen Sie diese Bedienungsanleitung vor dem
Gebrauch des Geräts aufmerksam durch, und
bewahren Sie sie für eine spätere Verwendung
auf.
Warnhinweis
- Halten Sie das Gerät trocken.
- Dieses Symbol bedeutet: Nicht unter
ießendem Wasser reinigen (Abb. 2).
- Dieses Gerät kann von Kindern ab
8 Jahren und Personen mit verringerten
physischen, sensorischen oder psychischen
Fähigkeiten oder Mangel an Erfahrung und
Kenntnis verwendet werden, wenn sie
bei der Verwendung beaufsichtigt werden
oder Anweisung zum sicheren Gebrauch
des Geräts erhalten und die Gefahren
verstanden haben.
- Reinigung und Pege des Geräts darf nicht
von Kindern durchgeführt werden, außer
Sie sind älter als 8 Jahre und beaufsichtigt.
- Bewahren Sie das Gerät und das Kabel
außerhalb der Reichweite von Kindern
unter 8 Jahren auf.
- Achten Sie darauf, dass Kinder nicht mit
dem Gerät spielen.
Loading ...
Loading ...
Loading ...