Loading ...
Loading ...
Loading ...
7
Mark Rear Wall
The microwave oven must be installed on a minimum of 1 wall
stud, preferably 2, using a minimum of 1 lag screw, preferably 2.
1. Using measuring tape, find and clearly mark the vertical
centerline of the opening.
2. Align the center markers on the wall template to the
centerline on the wall, making sure it is level and that
the top of the wall template is butted up against the
bottom edge of the upper cabinet.
NOTES:
■ If the front edge of the upper cabinet is lower than the back
edge, lower the wall template so that its top is level with the
front edge of the cabinet.
■ If the wall template is damaged or unusable, measure and
mark the wall with the dimensions described in Step 4.
3. Tape the wall template in place. Mark both holes in the lower
corners, and draw a horizontal line across the bottom edge
of the wall template. These represent the mounting plate’s
end holes and bottom edge.
4. Remove the wall template and check the markings:
■ The bottom edge line must be 17
1
/
4
" (43.8 cm) from
the bottom of the upper cabinet and must be level.
■ The end holes must be 15
3
/
4
" (40 cm) from the bottom
edge of the upper cabinet and must be on a level line
with each other. They must each be 14
1
/
8
" (35.9 cm)
from the centerline.
5. With the support tabs facing forward (see illustrations in
“Locate Wall Stud(s)” section), align the mounting plate
center markers to the centerline on the wall, making sure
its bottom edge is aligned to the horizontal line drawn in
Step 3, and that the end holes are properly marked. Make
sure the mounting plate is level.
6. Holding the mounting plate in place, find the wall stud
centerline(s) drawn in Step 2 of “Locate Wall Stud(s),” and
mark at least 1, preferably 2, hole(s) through the mounting
plate closest to the wall stud centerline(s). See figures 1, 2
and/or 3 in “Possible Wall Stud Configurations” in “Locate
Wall Stud(s)” section. The blackened holes in the shaded
areas are ideal hole locations.
7. Set the mounting plate aside.
Wall Venting Installation Only
8. Mark the centerline 3/8" (1 cm) down from the bottom
edge of the upper cabinet.
9. Using measuring tape, measure out 6" (15.2 cm)
on both sides of the centerline, and mark.
10. Measure down 4" (10.2 cm) from the mark made in Step 8,
and mark.
11. Using a straightedge, draw the 2 horizontal, level
lines through the marks made in steps 8 and 10.
12. Draw the 2 vertical, plumb lines down from the marks made
in Step 9 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle.
This is the venting cutout area.
13. Cut a 3/4" (19 mm) hole in one corner of the cutout area.
14. Using a keyhole saw, cut out the venting cutout area.
Drill Holes in Rear Wall
In addition to being installed on at least 1 wall stud, the
mounting plate must attach to the wall at both end holes.
If the end holes are not over wall studs, use two 3/16-24 x 3"
round-head bolts with toggle nuts; if 1 end hole is over a wall
stud, use 1 lag screw and one 3/16-24 x 3" round-head bolt
with toggle nut; or if both end holes are over wall studs, use
2 lag screws. Following are 3 installation configurations.
Installation for No Wall Studs at End Holes
(Figures 1 and 2)
1. Drill 5/8" (16 mm) holes through the wall at both end holes
marked in Step 3 of “Mark Rear Wall.”
2. Drill 3/16" (5 mm) hole(s) into the wall stud(s) at the
hole(s) marked in Step 6 of “Mark Rear Wall.” Refer
to figures 1 and 2 in “Possible Wall Stud Configurations”
in “Locate Wall Stud(s)” section.
Installation for Wall Stud at One End Hole (Figure 3)
1. Drill a 3/16" (5 mm) hole into the wall stud at the end
hole marked in Step 3 of “Mark Rear Wall.”
2. If installing on a second wall stud, drill a 3/16" (5 mm)
hole into the wall stud at the other hole marked in Step 6
of “Mark Rear Wall.” Refer to Figure 3 in “Possible Wall
Stud Configurations” in “Locate Wall Stud(s)” section.
3. Drill a 5/8" (16 mm) hole through the wall at the other
end hole.
Installation for Wall Studs at Both End Holes (Figure 4)
1. Drill 3/16" (5 mm) holes into the studs at the end
holes marked in Step 3 of “Mark Rear Wall.”
A
A. Centerline
A
C
B
D
A. Rear wall
B. Wall template
C. Top of wall template must align
with front edge of cabinet.
D. Front edge of upper cabinet
Upper cabinet bottom
Bottom of mounting plate
Mounting plate end hole
15³⁄₄"
(40.0 cm)
17¹⁄₄"
(43.8 cm)
14¹⁄₈"
(35.9 cm)
14¹⁄₈"
(35.9 cm)
Centerline
6" (15.2 cm) 6" (15.2 cm)
³⁄₈" (1 cm)
Upper cabinet bottom
4" (10.2 cm)
Centerline
Loading ...
Loading ...
Loading ...