1 2
876
3
9
4
10
5
11
SPECIAL FEATURES:
Your trimmer has been designed with several advanced
features to help you get perfect results every time you
trim. Your trimmer may be used to neatly trim goatees,
beards, mustaches, neckline, sideburns around the ears
and eyebrows, or anywhere you may need grooming.
It also makes a great all-around family trimmer for light
haircuts and touch ups between trips to the barber or to
clean up the shape of the neck.
A Detachable Blade System enables you to quickly
change from a standard-width blade for full grooming
to a narrow-width blade for detail trimming around a
mustache, goatee, or anywhere to define the hair line
and clip any stray whiskers.
To remove attachment, simply pull
top edge of blade away from body
unit. To attach, align back tab of
attachment head to cavity on the inner edge of trimmer unit and
push down on top of blade.
Should blades become damaged or dull or if you want additional
attachment heads for your trimmer, you may purchase them
from Wahl. See the ACCESSORY SHEET in this kit for ordering
information.
Self-Sharpening Blades are made to maintain their shape and
sharpness for extended periods.
TRIMMING WITH
ATTACHMENT COMBS
These attachments are ideal for blending,
tapering and defining beards, as well as for
achieving a “close trim” stubble look around
the face. To use the attachments, go with the
hair direction. To achieve closer looks, go against the hair direction.
To attach guide combs, hold comb with the teeth up. Snap guide
comb attachment firmly to the bottom of the trimmer blade.
SAVE THESE INSTRUCTIONS
For Household Use Only
RECHARGING & SMART LED
1. This trimmer is conveniently designed for household use. It
should be allowed to charge completely before its first use.
2. Remove the trimmer, recharging transformer and accessories
from the packing material.
3. Connect the transformer to the trimmer. BE SURE TRIMMER IS
IN THE “OFF - 0” POSITION WHEN CHARGING.
4. Plug the recharging transformer into any convenient electrical
outlet at the correct voltage.
5. When charging the trimmer, the LED will pulse.
6. When charging is completed, the LED will stay ON.
7. When the trimmer is about to run out of energy, the LED will
flash to indicate that you have less than 15% battery capacity
remaining. Once flashing starts, there should be enough charge
remaining to finish trimming before re-charging the trimmer.
8. Once the LED begins flashing to indicate that it needs to
be re-charged, it will remain flashing until the trimmer is
completely re-charged or until the trimmer runs out of power.
Completely recharged means that enough
charge time has elapsed and the LED stays
ON.
9. When trimmer is low in power, it should be
connected to the transformer and plugged
into an outlet to assure maximum power is
available when it is next used. This transformer is designed to
completely charge the battery without overcharging. Do not use
the trimmer while it is charging.
10. The battery will take approximately 60 minutes to charge. The
lithium ion trimmer also has quick charge capability. Quick
charge means for every minute you charge the trimmer, you
CARING FOR YOUR TRIMMER
OILING BLADES
For best results, use Wahl Clipper Oil on the blades only when
necessary, or approximately once a month. Motor bearings are
permanently lubricated—do not attempt to oil.
When oiling your trimmer, turn the trimmer “ON - I,” hold the unit
with the blades facing DOWN and squeeze three drops across the
front of the blade and one drop on each side on the heel of the
blade. Wipe off excess oil with soft cloth.
NOTICE—DO NOT OVER OIL!
Excessive oiling or application of
liquids will cause damage if allowed
to seep back into motor.
BLADE CARE
Trimmer blades have precision-hardened, ground and lapped
cutting teeth. Blades should be handled carefully and never
bumped or used to cut dirty or abrasive material. Clean with the
included brush.
Heads should be removed from the trimmer prior to
rinsing in water. After rinsing, allow the heads to air dry
completely before reattaching to the trimmer body. The
trimmer body should always be kept away from water
to maximize the life of the motor, battery, and control
components.
CLEANING/STORAGE
Before storing your trimmer, use the cleaning brush to whisk
any loose hairs from the unit and the blades. Store unit in such a
manner so that blades are protected from damage.
When the trimmer is not in use, the trimmer blade guard
attachment should be in place to protect the blades.
This appliance should be stored in a manner where it is not
subjected to crushing, heating above 100°C (212°F), or
incineration.
LITHIUM-ION BATTERY
REPLACEMENT, CLIPPER DISPOSAL
AND RECYCLING:
• For battery replacement send the entire, intact clipper unit to:
Wahl Annex 3001 North Locust, P.O. Box 578, Sterling, IL 61081
• Do not attempt to remove the battery. Lithium-Ion batteries can
explode, catch fire, and/or cause burns if disassembled, damaged,
or exposed to water or high temperatures.
• If you choose not to replace the battery, the entire, intact clipper
unit must be disposed. Do not attempt to remove the battery for
disposal. Lithium-Ion batteries may be subject to local disposal
regulations. Many locations prohibit disposal in standard waste
receptacles. Check your local laws and regulations.
• For recycling contact a government recycling agency, waste
disposal service, retailer, or visit online recycling sources, such as
www.batteryrecycling.com or www.rbrc.org.
TRAVEL LOCK
This Wahl trimmer comes with an electronic travel lock to avoid
accidental activation while transporting.
Hold power button down for 5 seconds to engage travel lock.
Hold power button down for 5 seconds to disengage travel lock.
NOTE: Plugging in power cord while locked will deactivate the
travel lock.
can get approximately 5 minutes of usage. For example, if you
are in a hurry, charging for 3 minutes will give you 15 minutes
of run time.
11. Insert only recharging transformer plug supplied by the
manufacturer into charger receptacle.
TROUBLESHOOTING
• If the LED did not flash before the trimmer stopped running try
resetting the trimmer by charging the trimmer completely until
the LED stays ON.
• Trimming is disabled when charging.
• If the trimmer unexpectedly stopped operating try resetting the
device by plugging the trimmer into the charger.
• If your trimmer does not seem to take a charge, check the
following before returning it for repair:
1. Check outlet to make sure it is working by plugging in another
appliance.
2. Make sure the outlet simply is not connected to a light switch
which turns the power at the outlet off when lights are turned
off.
3. Be sure the trimmer is properly connected to the recharging
transformer, all connections are secure and the trimmer is
turned off.
4. If your electricity is connected to a master power switch,
we suggest the trimmer be disconnected from the charger
anytime the master switch is off. Leaving the unit plugged into
a dead outlet or an unplugged charger will drain the battery.
5. If trimmer does not run and it is completely charged, turn
the unit “ON - I” and pinch or push the blades manually.
(Oil may have dried out between the blades, so they may be
temporarily stuck together.)
Operating Instructions for the
Lithium Ion Trimmer
Instrucciones de Operación
de la Recortadora de Litio Ion
WahlUSA.com
TRIMMING AND EDGING YOUR
BEARD
The following are suggested trimming steps and trimmer
positions. You may find different procedures work better for you.
1. Comb your beard in the direction that it grows to help reveal
stray hairs that may be longer than the others.
2. Attach a guide to trim and taper your beard. Begin with a guide
of a long trimming length. Trim toward your chin in smooth,
overlapping strokes, following the lay of your beard. If you trim
against the way your beard naturally lays, the trimmer will cut
the hair much shorter.
Change the trimming guides to progressively shorter lengths
until you reach the desired length of beard. You may wish to
trim closer near the ear and down
under the chin, changing to a longer
guide toward the front of the face and
point of your chin.
3. To cut the outline of your beard,
remove the trimming guide comb.
Starting under your chin and working
back toward your jawbone and ears,
cut the outer perimeter of your beard
underneath the jawbone. Continue
the line all the way up to the ears and
hairline.
4. Accentuate your beard line by using
the trimmer in a downward motion.
Start at the line you’ve created and,
working from the chin back toward the
ears, trim the area right under your
beard line.
5. Define the upper part of your beard
using the same technique.
CUTTING HAIR
The first time you cut the hair, cut only a small amount until you
become accustomed to how long each guide comb leaves the hair.
Always start by placing the largest guide comb on the trimmer, then
use shorter combs if a shorter length is desired.
Remember, between professional haircuts, the hair grows evenly all
over the head and a light trimming at the lower neck and sides may
be all that is needed to bring back that neat, well-groomed look.
For uniform cutting, allow the trimmer to cut its way through the
hair. Do not force it through at a faster rate.
1. Start by combing the hair so it falls into its natural direction.
2. Place the largest guide comb onto your trimmer and start by
trimming the sides from the bottom upwards. Hold the trimmer
lightly against the hair, with teeth of the guide comb pointing up
but flat against the head. Slowly lift the trimmer up and outward
through the hair, cutting only a small amount at a time.
Repeat around sides and back of head.
If you desire shorter hair, either change to a shorter guide comb or
apply more pressure and less lift away from head with the present
attachment.
This entire procedure requires practice, and it is always better to
leave too much hair the first few haircuts.
6. For a neater finished look, attach the
detail blade. Use this blade for fine,
detail trimming anywhere it is needed,
such as at the sideburns near the ears,
goatees, etc.
DETAILING NECKLINES,
SIDEBURNS,MUSTACHES & BEARDS
Slowly move trimmer downward on desired areas to neatly
trim and shape.
TRIMMING ARM & LEG HAIR
Simply glide the trimmer over your arm or leg until desired hair
length is achieved. The first time you trim the hair, start by using a
longer guide comb on the trimmer, then use progressively shorter
settings if a shorter length is preferred.
TRIMMING CHEST & STOMACH
Glide the trimmer over your torso region, in an upward motion
until desired hair length is achieved. For tight, scratch-free
trimming, use the #1/4 guide comb.
TRIMMING NOSE HAIR
Make sure the nasal passages are clean. Slowly move the ear/nose
trimmer in and out of each nostril, no more than 1/4-inch deep.
TRIMMING EAR HAIR
Make sure the outer areas of the ears do not contain any wax. Hold
the ear flat with one hand and carefully insert ear/nose trimmer no
more than 1/4-inch into the outer ear.
CAUTION:
Do not insert the detailer or any other foreign
object into the inner ear. For hair growing on the outside of the ear,
simply move the detailer slowly along the edges of the ear.
TRIMMING EYEBROWS
Slowly move detailer to neatly trim stray hairs. For precise, even
trimming, slowly move the detailer closer or farther away from
eyebrows to achieve desired length. Do not press against brow as it
may remove too much hair.
FADE CUT
1. Start at the temple and cut all the way around the head to
establish the ultimate location of the fade line. Always cut
against the grain for the shortest cut. Don’t force the blade
through the hair. Let the trimmer do the work.
2. Next, cut around the head again and up the nape of the neck
to the fade line, brushing away the cut hair as you go. Pull the
scalp taut with the thumb for the closest cut. Turn the trimmer
upside down when necessary to keep cutting against the grain.
Make sure both sides of the head are even.
3. For the top of the head, cut with the grain using the individual
guide comb attachments. The smaller the number of the comb,
the shorter the cut. Comb or brush the hair as you cut for an
even end result.
4. To complete the fade, blend the hair at the fade line by trimming
up and out across the line and against the grain all the way
around the head. Then, repeat all around, turning the trimmer
upside down and cutting downward. The final objective is to
blend the hair so there is no real line, just a perfect fade from
bald to very short hair. You can achieve this by using the #1
guide comb attachment. Continue combing and cutting until you
achieve the desired effect.
5. To create a part, pick a spot off-center. Pull the scalp tight and
with the end of the blade perpendicular to the head, move the
trimmer back and forth to cut a line. Comb through it and cut
again to make sure the cut is precise.
© 2019 Wahl Clipper Corporation
Part No. 92553-001
Printed in China
For more information or Product Registration, visit WahlUSA.com
5-YEAR LIMITED WARRANTY
Valid in U.S.A. Only
If your Wahl product fails to operate satisfactorily within five (5)
years from the date of original purchase or receipt as a gift, Wahl
will, at our option, repair or replace the product and return it to
you FREE OF CHARGE. Do not return this product to store where
purchased. Products needing repair under this warranty should
be returned with postage pre-paid to the following address or call
1-800-767-9245 for assistance:
Wahl Clipper Corp.
Attn: Repair Department
3001 Locust Street
Sterling, Illinois 61081
When mailing, please include a note describing the defect and
the date of original purchase or receipt as a gift. Products out of
warranty will be repaired at our standard repair charges.
This warranty does not cover products damaged by:
1. Modification or repair by anyone other than Wahl Clipper
Corporation or a Wahl authorized service center;
2. Commercial (non-consumer) use or unreasonable use.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. No other written
express warranty is given. No responsibility is assumed for
incidental or consequential damages of any type or for the use
of unauthorized attachments. Some states may not allow the
exclusion or limitation of incidental or consequential damages, so
the limitation may not apply to you. Warranty valid in U.S.A. only.
Outside U.S.A., check with store for Wahl authorized distributor’s
warranty.
Lithium•Ion+
™
STAINLESS STEEL
Detachable Blade Trimmer
Recortadora con Láminas Desmontable
SERVICE AND REPAIR
If you have problems with your trimmer, send it prepaid with a note
explaining the problem to:
Wahl Clipper Corporation
Attn: Repair Department
3001 Locust Street
Sterling, IL 61081
Telephone (800) 767-9245
For products purchased outside the United States, contact your distributor.
If for any reason within 60 days of purchase of your Wahl
®
trimmer you are not satisfied with your trimmer and would like a
refund, just return your trimmer, together with the sales receipt, to
the retailer from whom you purchased it. Wahl will reimburse all
retailers who accept trimmers within 60 days of purchase. If you
have any questions regarding this money-back guarantee, please
call 1-800-767-9245 in the United States.
60 Day Money Back Guarantee!
Loading ...
