Loading ...
CONVERTING TO PROPANE GAS (OR CONVERTING BACK
TO NATURAL GAS FROM PROPANE)
This cooktop leaves the factory set for use with natural gas. If you want to convert to
propane gas, the conversion must be performed by a qualified propane gas installer.
The conversion orifices and instructions can be found attached to the regulator.
Keep these instructions and all orifices in case you want to convert back to natural gas.
RECOMMENDED GAS
SUPPLY LOCATION FROM
BACKWALL
OVERALL COOKTOP DIMENSIONS
CUTOUT DIMENSIONS OF COUNTERTOP
To ensure accuracy, it is best to make a template when cutting the opening in the counter.
DIMENSIONS AND
CLEARANCES
Provide adequate clearances between the
cooktop and adjacent combustible surfaces.
These dimensions must be met for safe use of
your cooktop.
Allow 30” (76.2 cm) minimum clearance
between burners and bottom of unprotected
wood or metal cabinet, or allow a 24” (61
cm) minimum when bottom of wood or metal
cabinet is protected by no less than 1/4” (6.4
mm) thick flame-retardant millboard covered
with no less than No. 28 MSG sheet metal
(.015” [.38 mm] thick), .015” (.38 mm) thick
stainless steel, .025” (0.64 mm) aluminum or
.020” (0.5 mm) copper.
Installation of a listed microwave oven or
cooking appliance over the cooktop shall
conform to the installation instructions packed
with that appliance.
Built-in oven installation, shall conform to the
installation instruction packed with the built-in
oven.
MAINTAIN THE FOLLOWING MINIMUM CLEARANCE
DIMENSIONS
FOR AMERICANS WITH
DISABILITIES ACT (ADA)
FORWARD APPROACH
INSTALLATION ONLY
NOTE: The enclosure must be made of wood
material. Also, an access panel is required for
the electrical outlet, pressure regulator, shut-off
valve, hold-down brackets, and service.
1” Min. From Backwall
7″
From
Cutout
Center
Line
Recommended
gas supply
location
Allow 5” minimum depth
between the countertop
and an enclosure.
5”
NOTE: Allow 7/16” minimum vertical clearance from the cooktop
bottom (or 3-11/16” minimum depth from the countertop) to any
combustible surfaces, such as a cabinet drawer.
For island installation, maintain 2-1/2 in. minimum from cutout to front
and back edge of countertop. Maintain 3 in. minimum from cutout to
side edges of countertop.
3 3/4 MIN.
16″ MAX. Depth
of unprotected
overhead cabinets
18″ MIN. height
from countertop to
nearest cabinet on
either side of unit
30” or 36”
cabinet base
or wider
R - MIN. clearance
from cutout to right
side wall
L - MIN. clearance from
cooktop to left side wall
C - MIN. clearance
from cutout to rear wall
2-1/2” MIN from cutout
to front of countertop
30″ MIN. clearance
from countertop
to unprotected
overhead surface
ALL HORIZONTAL
CLEARANCES MUST
BE MAINTAINED FOR A
MINIMUM OF 18” ABOVE
THE COOKING SURFACE.
C L R
JGP3030, JGP3530, JGP3036 2-1/4” 6” 6”
JGP5030, PGP7030, CGP7030,
PGP9030, CGP9530
2-7/8” 12” 12”
JGP5036, PGP7036, CGP7036,
PGP9036, CGP9536
3-3/8” 12” 12”
7/16″
3-11/16″
DRAWER
DRAWER
Cooktop
33-3/4″
36″
21″
3-11/16″
19″
17″
33-7/8”
length
of cut
19-1/8” width cut
Cooktop
28-1/4″
30″
21″
3-11/16″
19-1/2″
30” Models 36” Models
14-1/4″
28-1/2”
length
of cut
19-5/8” width cut
30” Models 36” Models
1” = 2.5 cm; 1’ = 0.3 m
Loading ...
Loading ...
Loading ...