Loading ...
Loading ...
Loading ...
NOTE:
THE INITIAL SPIN AT THE BEGINNING OF THE WASHING CYCLE IS A NORMAL PHASE OF THE
PROGRAM AND NOT A MACHINE FAULT.
NOTE:
THE MACHINE IS FITTED WITH A SPECIAL ELECTRONIC DEVICE, WHICH PREVENTS THE SPIN CYCLE
SHOULD THE LOAD BE UNBALANCED.
THIS REDUCES THE NOISE AND VIBRATION IN THE MACHINE AND SO PROLONGS THE LIFE OF YOUR
MACHINE.
O fabricante declina toda a responsabilidade por possíveis erros de impressão que
possam haver neste manual. Assim, reserva-se o direito de efectuar as modificações
que se considerem úteis sem comprometer as características essenciais do produto.
La Ditta costruttrice declina ogni responsabilità per eventuali errori di stampa contenuti
nel presente libretto. Si riserva inoltre il diritto di apportare le modifiche che si
renderanno utili ai propri prodotti senza compromettere le caratteristiche essenziali.
.
,
.
La firma fabricante declina toda responsabilitad por los posibles errores de
impresión que puedan haber en este libreto. Asimismo, se reserva el
derecho de efectuar las modificaciones que se consideren ùtiles a sus
propios productos sin comprometer las caraterìsticas esenciales.
The manufacturer declines all responsibility in the event of any printing mistakes in
this booklet. The manufacturer also reserves the right to make appropriate
modifications to its products without changing the essential characteristics.
86
CHAPTER 13
EN
FAULT
If the fault should persist, contact a Candy Technical Assistance Centre. For prompt
servicing,give the model of the washing machine, to be found on the label placed on
the cabinet inside of the porthole or on the guarantee certificate.
Important
1The use of environment friendly detersives without phosphates may produce the
following effects:
- The discharge rinse water may result cloudier due to the presence of zeolites in
suspension. This does not compromise the efficiency of the rinses.
- The presence of white powder (zeolites) on the washing at the end of the washing
cycle. This does not remain incorporated in the fabric and does not alter the colour.
- The presence of foam in the last rinse water which is not necessarily a sign of
inadequate rinsing.
- The non-ionic surface-active agents present in the composition of washing
machine detersives are often difficult to remove from the washing itself and, even in
small quantities, may produce visible signs of the formation of foam.
- Carrying out further rinses, in cases such as this, is not useful.
2If your washing machine fails to function, carry out the above-mentioned checks
before calling the Candy Technical Assistance Service.
1. Does not function
on any
programme
2. Does not load
water
3. Does not
discharge water
4. Water on floor
around washing
machine
5. Does not spin
6. Strong vibrations
during spin
7. Display reads error
0, 1, 5, 7, 8, 9
8. Display reads
error 2
9. Display reads
error 3
10.Display reads
error 4
Mains plug not plugged in
Mains switch not on
No power
Electric circuit fuses failure
Load door open
See cause 1
Inlet tap turned off
Timer not set correctly
Discharge tube bent
Odd material blocking filter
Leak from the washer between the tap
and inlet tube
The washing machine has not
discharged water
“No spin”setting (some models only)
The presence of excessive foam has
aborted the spinning phase
Washing machine not perfectly level
Transport bracket not removed
Washing load not evenly distributed
–
No water fill.
No pump out.
Machine overfilled with water.
Insert plug
Turn on mains switch
Check
Check
Close load door
Check
Turn on water inlet tap
Set timer on correct position
Straighten discharge tube
Check filter
Replace washer and tighten the tube
on the tap
Wait a few minutes until the machine
discharges water
Turn the programme dial onto spin
setting
Do not use excessive amounts of
detergent
Adjust special feet
Remove transport bracket
Distribute the washing evenly
Call service.
Check water supplies are on.
Check drain is clear.
Check drain hose is not kinked.
Turn off water supply to machine.
Call service.
CAUSE
REMEDY
Loading ...