Loading ...
Loading ...
Loading ...
ZH
1110
Cleaning and care of the other parts of the appliance
• Unplug the appliance before cleaning.
• Clean the outside of the Rice Cooker – g.18, the inside of the lid – g.13 and the cord with
a damp cloth and wipe dry. Do not use abrasive products.
• Do not use water to clean the interior of the appliance body as it could damage the heat
sensor.
TECHNICAL TROUBLESHOOTING GUIDE
Remark: if inner bowl is deformed, do not use it anymore and get a replacement from
the authorized service center for repai
Malfunction
description
Causes Solutions
Any indicator lamp
off and no heating.
Rice cooker not plugged.
Verify the main plug is well engaged in the
product body.
Any indicator lamp
off and heating.
Problem of the connection of
the indicator lamp or indicator
lamp is damaged.
Send to the authorized service center for
repair.
Steam leakage
during using.
Lid is badly closed. Open and close again the lid.
Micro pressure valve not well
positioned or uncomplete.
Stop the cooking (unplug the product) and
check the valve is complete (2 parts locked
together) and well positioned.
Lid or micro pressure valve
gasket is damaged.
Send to the authorized service center for
repair.
Rice half cooked or
overtime cooking.
Too much or not enough water
compared to rice quantity.
Refer to table for water quantity.
Automatic warm-
keeping fails
(product stay in
cooking position, or
no heating).
Send to authorized service center for repair.
E0
The sensor on the top open
circuit or short circuit.
Send to the authorized service center for
repair.
E1
The sensor on the bottom open
or short circuit.
E2
The sensor of inductor open or
short cirucuit.
E3 High temperature detected.
Stop the appliance and restart the program.
If the problem repeats, please send to the
authorized service center for repair.
E5 Missing bowl.
Put the inner pot inside the appliance, then
unplug and re-plug the appliance and finally
restart the program.
第一次使用前
取出設備
• 將設備從包裝中取出並拆開所有配件和文件。
• 按位於外殼上的開蓋按鈕，打開蓋子 - 圖1.
閱讀說明書並仔細遵循操作方法。
清潔設備
• 取出內鍋 – 圖 2、內蓋以及微壓閥– 圖 3a 和 3b.
• 用海綿和洗潔精將內鍋、微壓閥以及內蓋洗淨。
• 用濕布擦拭設備外部以及蓋子。
• 仔細擦乾。
• 將所有的部件放回初始位置。將內蓋安裝到機器頂蓋的正確位置上。然後，將內蓋
放到兩個勾位後並在頂部推動它，直至固定。將可拆式電源線安裝到電飯煲底的電源
接口上。
設備
• 該電飯煲具備16種功能。日本米、白米、糙米、正常、軟、硬、快煮、蒸煮、少
量、湯、粥、稀飯、翻熱、保溫、預設以及可調校計時器。
• 當電源線接通插座和電飯煲的電源接口時，控制面板上的所有指示燈都將亮起片
刻。
• 在烹調時間結束時，設備將自動切換至保溫模式，持續24小時。
• 接通電源或烹調後，切勿碰觸設備內部的表面。
• 切勿在使用中或剛烹調完後搬動產品。
烹調前準備
量度材料——鍋的最大容量
• 鍋內側的刻度標記單位為升和杯，用於測量煮飯時的用水量。
• 隨設備一起提供的塑膠量杯用於量米，而不是量水。1 量杯的米重量約為150g。
• 使用者可以根據米的類型以及他們的口味偏好減少或增加水。
• 由於不同地區的電壓不同，水和米少量外溢屬正常現象。
• 水+米的最大量不應超過鍋內的最高刻度。
添加的材料或水不得超過最高刻度。
煮飯時
• 在煮飯前，用量杯量米，並將米沖洗。
• 將沖洗後的米放入鍋內，並加水至相應的水位（杯內的刻度）。
• 加水量可根據個人口味進行調整。
Loading ...
Loading ...
Loading ...