Loading ...
Loading ...
Loading ...
Installation and connection en
9
■ Use the residual heat. For longer cooking times, you
can switch the hotplate off 5-10 minutes before the
end of the cooking time.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
5Installation and connection
Instal l ati on and c onnect i on
'R QRW LQVWDOO WKH DSSOLDQFH EHKLQG D GHFRUDWLYH GRRU RU WKH GRRU
RIDNLWFKHQXQLWDVWKLVPD\FDXVHWKHDSSOLDQFHWRRYHUKHDW
Electrical connection
Only licensed specialists may connect the appliance.It
is important that you comply with the requirements of
your electricity supplier.
Any damage arising from the appliance being
connected incorrectly will invalidate the warranty.
Caution!
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
:Warning – Danger of death!
There is a risk of electric shock if you touch live
components.
■ Always make sure your hands are dry when you
touch or hold the mains plug.
■ Only pull out the mains cable by taking hold of the
plug and removing the plug; never pull it out by the
mains cable itself, as this could damage it.
■ Never unplug the mains plug when the appliance is
in operation.
Please note the following information and ensure that:
Notes
■ The mains plug fits the socket.
■ The cable cross section is adequate.
■ The earthing system is properly installed.
■ The mains cable is only replaced by a qualified
electrician (if this is necessary).Spare mains cables
can be ordered from our after-sales service.
■ No power strips/multi-way connectors or extension
cables are used.
■ If using a residual current device, only use one that
bears the mark z.
The presence of this mark is the only way to be sure
that it fulfils all the applicable regulations.
■ The mains plug can be accessed at all times.
■ The mains cable is not kinked, crushed, modified or
severed.
■ The mains cable does not come into contact with
heat sources.
For the installer
■ An all-pole isolating switch with a contact gap of at
least 3 mm must be present in the installation circuit.
This is not necessary if the appliance is connected
by a plug that is accessible to the user.
■ Electrical safety: The cooker corresponds to safety
class I and may only be used in conjunction with a
safety earth terminal.
■ A type H 05 VV-F or equally rated lead must be used
to connect the appliance.
Levelling the cooker
Always place the cooker directly on the floor.
1. Pull out the plinth drawer and lift it up and out.
There are adjustable feet at the front and rear on the
inside of the plinth.
2. Use an Allen key to raise or lower the adjustable feet
as necessary until the cooker is level (picture A).
3. Push the plinth drawer back in (picture B).
Adjacent units
Any adjacent units must not be made of flammable
materials. The fronts of any adjacent units must be heat-
resistant up to at least 90 °C.
Wall fixing
To prevent the cooker from tipping over, you must fix it
to the wall using the enclosed bracket. Please observe
the installation instructions for fixing the oven to the
wall.
Measures to be noted during transport
Secure all mobile parts in and on the appliance using
an adhesive tape that can be removed without leaving
any traces. Push all accessories (e.g. baking tray) into
the corresponding slots with cardboard at the edges, in
order to avoid damaging the appliance. Place
cardboard or similar between the front and rear side to
prevent knocks against the inside of the glass door.
Secure the door and, if available, the top cover to the
appliance sides using adhesive tape.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment -
WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
%$
Loading ...
Loading ...
Loading ...