Loading ...
Loading ...
Loading ...
8
Mark holes
1 Select the vent option that your installation will require
and proceed to that section:
Outside top exhaust
(Vertical duct– 3
1
⁄4”x 10” Rectangular)
Use the diagram or the hood as a template and mark the
locations on the cabinet for ductwork, electrical wiring and
keyhole screw slots.
Centerline Electrical access
hole (in cabinet
bottom)
Wood shims (recessed
bottom cabinets only)
Hood mounting screws (4)
13
15
⁄16” (30” hood)
16
15
⁄16” (36” Hood)
13
15
⁄16” (30” hood)
16
15
⁄16” (36” Hood)
Cabinet front
Cabinet bottom
12
1
⁄2”
5
1
⁄4”
5
1
⁄4”
1
1
⁄4”
1
1
⁄4”
1
1
⁄2”
10
1
⁄2”
5”
Vertical duct
access hole
Outside top exhaust (Only recirculating version)
(Vertical duct–7” Round)
Use the diagram or the hood as a template and mark the
locations on the cabinet for ductwork, electrical wiring and
keyhole screw slots.
Wood shims (recessed
bottom cabinets only)
Hood mounting screws (4)
13
15
16” (30” hood)
16
15
16” (36” Hood)
13
15
16” (30” hood)
16
15
16” (36” Hood)
Cabinet front
Cabinet bottom
12
1
2”
1
1
4”
1
1
2”
10
1
2”
5”
HOLE
Access hole for
7” round duct
Centerline
Electrical access hole
(in cabinet bottom)
8” DIA.
Outside rear exhaust
(Horizontal duct– 3
1
⁄4”x 10” Rectangular)
Use the diagram or the hood as a template and mark the
locations on the cabinet for ductwork, electrical wiring and
keyhole screw slots.
Centerline
Electrical access hole
(in wall)
Cabinet
bottom
Horizontal duct
access hole
Hood mounting
screws (4)
Cabinet front
13
15
16” (30” hood)
16
15
16
” (36” Hood)
13
15
16” (30” hood)
16
15
16
” (36” Hood)
1
9
16”
3
3
4
5
1
4
”
”5
1
4
”
12
7
16
”
1
8”
Installation- Recirculating
Use the hood as a template and mark the locations on the
cabinet for the electrical wiring and keyhole screw slots.
Since the hood is to be recirculated (not to be vented outside),
do not cut out any vent openings in the wall or cabinet bottom.
Choose Venting Option
1 The hood can be set to vent outside or to recirculate air
back into the kitchen. The plastic vent lever is located near
the center of the hood opening.
To vent to the outside, make sure the plastic vent lever is
in the HORIZONTAL position (flat against the metal top
of the hood). To recirculate air into the kitchen, make sure
the plastic vent lever is in the VERTICAL position
(flat against the plastic blower housing).
NOTE: In order to change the vent lever position, you will
need to pull the lever out slightly to clear the plastic tabs.
Hood shown lying upside down
Set for
outside venting
Set for
recirculating
Stop tab
Stop tab
For recessed bottom cabinet only
1 If the cabinets have front, side or back trim, make 2 wood
shims the width of the trim and attach them to the cabinet
bottom recess on both sides.
See previous page for marking locations.
Wood shims
2 Cut holes at marked locations for duct and electrical
wiring. For the vertical duct, cut out
3
⁄4” extra toward the
front of the cabinet so you can move the duct freely when
installing the hood. It may also ease installation by cutting
the hole 10
1
⁄ 2” instead of 10”.
3 Drive a mounting screw (from the hardware packet)
partway into each center of the narrow neck of the keyhole
slots marked on the cabinet bottom.
4 Fix the wiring conduit to the hood.
5 Slide the hood back against the wall. Tighten the mounting
screws. Be sure the screw heads are in the narrow neck of
the keyhole slot. Connect Ductwork to hood.
Loading ...
Loading ...
Loading ...