Ed : 08/14 Rev : 00 Cod :
INSTRUCTION
GRLDEVEFROWSMA
ASSEMBLY INSTRUCTIONS
STEP 1
Attach the FRONT STABILIZER(3) to the CENTER BEAM(2) with CARRIAGE BOLTS(M8x1.25x40mm)
(23), WASHERS(M8)(12), and ACORN NUTS(M8x1.25)(14).
STEP 2
Refer to the illustration below and detail view A. Attach the SEAT(7) to the SEAT CARRIAGE(5) with BUTTON
HEAD BOLTS(M8x1.25x15mm)(21) and WASHERS(M8)(12). Slide the twoSECURING ROLLERS(33)
to the shafts on the SEAT CARRIAGE(5). Slide the SEAT CARRIAGE ASSEMBLY(5) onto the CENTER
BEAM(2).
A.
7
ASSEMBLY INSTRUCTIONS
STEP 3
Insert the STOPPER SHAFT(30) through the hole in the CENTER BEAM(2). Screw two STOPPERS(29)
onto both ends of the STOPPER SHAFT(30) and tighten at the same time.
STEP 4
Attach the REAR SUPPORT(1) to the CENTER BEAM(2) with BUTTON HEAD BOLTS(M8x1.25x15mm)
(21) and WASHERS(M8)(12). Press The OVAL CAP(31) into the back end of the CENTER BEAM(2).
STEP 5
Attach the SHOCK(10) to the bracket at the front of theCENTER BEAM(2) with BUTTON HEAD BOLT
(M8x1.25x42mm)(11), WASHERS(M8)(12), and NYLOCK NUT(M8x1.25)(13).
8
ASSEMBLY INSTRUCTIONS
STEP 6
Attach the ROWING ARM(43) to the CENTER BEAM(2) with BUTTON HEAD BOLT(M10x1.5x80mm)(26),
WASHERS(M10)(27), and NYLOCK NUT(M10x1.5)(28). Connect the SHOCK(10) to one of the adjustment
holes on theR OWING ARM(43) and secure with theLOCKING KNOB(44) and theADJUSTMENT
KNOB(45). Refer to the detail view below. The shoulder of the LOCKING KNOB(44) and end of the
ADJUSTMENT KNOB(45) must be inserted into one of the adjustment holes.
STEP 7
Insert the HANDLEBAR(6)through the tube on the top of the ROWING ARM(4). ress two HAND GRIPS(9)
onto both ends of the HANDLEBAR(6).
STEP 8
Install aAA battery into the METER(8), the battery is not included .ee page 11 for detailed battery installation
instructions. Slide the METER(8) onto the plate on the ROWING ARM(4).
Shoulder of the
Locking Knob.
Adjustment
Holes
End of the
Adjustment Knob.
9
ASSEMBLY INSTRUCTIONS
STEP 9
Insert the PEDAL SHAFT(19) through holes located on the CENTER BEAM(2). lide a PEDAL SPACER(20)
and a PEDAL CAP(18) onto each end of thePEDAL SHAFT(19). Then secure thePEDAL CAPS(18)
with BUTTON HEAD BOLTS(M8x1.25x15mm)(21) and LARGE WASHERS(M8)(22) at both ends of the
PEDAL SHAFT(19).
NOTE: You need to use two Allen Wrenches to tighten the BUTTON HEAD BOLTS(M8x1.25x15mm)(21)
at both ends of the PEDAL SHAFT(19) at the same time.
10
USE INSTRUCTIONS
USING THE FITNESS METER
POWER ON :
POWER OFF :
Handlebar movement
Automatic shut off after four minutes of inactivity.
STROKES
/MIN
SCANN
CNT
TIME
CAL
FUNCTION BUTTONS:
MODE : Press to select the function of the lower readout.
RESET : To reset all functions to zero.
M
R
FUNCTIONS:
COUNT :
SCAN:
TIME:
STROKES/MIN:
CALORIE:
NOTE: 1.
2.
Upper readout displays the total number of strokes you have taken from zero to 9999
strokes.
Automatically scans each function of TIME, CALORIE, STROKES/MIN in sequence with
change every six seconds.
Displays the workout time from one second up to 99:59 minutes.
Displays the rate of strokes per minute.
Displays the calorie burned from zero to 9999 cal.
The calorie readout is an estimate for an average user. It should be used only as a
comparison between workouts on this unit.
The meter will stop counting time automatically after six seconds of inactivity. All function
values will be kept. Restart the meter by rowing the handlebar or press any button.
The meter will shut off automatically after four minutes of inactivity. All function values will
be kept. Press the RESET button to reset all functions to zero.
HOW TO INSTALL AND REPLACE BATTERIES:
1. Open the Battery Door on the back of the meter.
2. The meter operates with an AA battery.
Refer to the illustration to install or replace the battery.
NOTE:
1. Rechargeable batteries are not recommended.
AA Battery
11
D
SE
PRODUCT PARTS DRAWING
FRONT
16
GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy
www.evert.it - info@evert.it
