Intex 28635EG User Manual

Loading ...

(107) MODEL 635T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/22/2016

107

SAVE THESE INSTRUCTIONS

English

Page 14

TROUBLESHOOTING GUIDE

• Filtercordmustbepluggedintoa3wire 

outlet that is protected by a Class A

 GroundFaultCircuitInterrupter.

• Resetcircuitbreaker.Ifcircuitbreakertrips

repeatedly, your electrical system may

have a defect. Turn off circuit breaker and

call an electrician to correct the problem.

• Letmotorcooldown.

• AdjustthechlorineandpHlevel.Consult 

your local swimming pool supply stores.

• Cleanorreplacecartridge.

• Checkthecartridgeforholes.Replaceif 

damaged.

• Operatethefilterforlongerperiods.

• Cleanthestrainerscreenattheinlet.

• Clearanyobstructionsintheintakehoseby

discharging it inside pool wall.

• Tightenhosenuts,checkhosesfordamage,

check pool water level.

• Cleancartridgemoreoften.

• Cleaninsidetheplungervalve.

• Pullvalvehandletofulluprightposition.

• Installthenozzleattheupperpositionofthepool

inlet, and the strainer at the lower position of the

pool outlet.

• Makesuretheinletthreadedairconnectoris

connected to the pool inlet upper hole.

•Fillpooltocorrectwaterlevel.

• Cleanstrainerscreensatpoolinlet.

• Tightenhosenuts,checkhosefordamage.

• Clearanysticksorleavesintheintakehose.

• Turnandpullvalvehandletofulluprightposition.

• Removecover&checkforO-ring.

• Tightencoverorvalve(Manually).

• Tightenorreinstallhosenut.

• Puttheo-ringbackintothegroove.

• Replace a new hose.

• Openairreleasevalve,waituntilwaterstarts

to flow out of the air release valve, close air

release valve.

• Thelowerpositionofpooloutletconnectstofilter

pump water inlet. The upper position of pool inlet

connects to filter pump water outlet.

• Tightenorreinstallplungervalve.

• Tightenairjetvalveandmakesureit’s

facing up.

• TurnpumpONandrunforfewseconds,then

 turnOFF,repeat3times.

• Removeairjetvalve,flushdirtoutwithwaterand

replace valve back.

• Replaceanewairjetvalve.

FILTERMOTOR

FAILSTOSTART

FILTERDOESN’T

CLEANPOOL

FILTERDOESN’T

PUMPWATEROR

THEWATERFLOW

ISVERYSLOW

PUMPDOESN’T

WORK

TOPCOVER

LEAKING

HOSELEAKING

AIRLOCK

INLETTREADED

AIRCONNECTOR

/AIRJETVALVE

LEAKING

• Themotorisnotpluggedin.

• TheGFCIcircuitbreakeris 

tripped.

• Motortoohotandoverload 

protection shut motor off.

• ImproperchlorineorpH 

levels.

• Filtercartridgeisdirty.

• Damagedcartridge.

• Excessivelydirtypool.

• Thestrainerscreenis  

restricting the water flow.

• Cloggedinletordischarge.

• Anairleakontheintakeline.

• Scaleorbuilduponcartridge.

• Excessivelydirtypool.

• Dirtyfiltercartridge.

• Thenozzleandstrainer

connection are reversed.

• Inletthreadedairconnector

connected to the wrong hole on

the liner.

• Lowwaterlevel.

• Strainerscreenpluggedup.

• Anairleakontheintakehose.

• Faultymotorortheimpelleris 

jammed.

• Anairlockinsidethecartridge 

chamber.

• O-ringmissing.

• Coverorairreleasevalvearenot

tight.

• Hosenutsarenotwell-fitted.

• Hoseo-ringdislodgedwhen

connecting the hose.

• Hosebroken.

•There’sairtrappedinthe 

pump housing and inlet hose.

•Theinletandoutlethoses 

connection are reversed.

• Plungervalvenotwell-fitted.

• Airjetvalveisnottightand

facing up.

• Airjetvalveinternalsealblocked.

• Airjetvalveinternalsealdirty.

• Airjetvalvebroken.

TROUBLE CAUSE SOLUTION

Loading ...

Intex 28635EG - Krystal Clear Cartridge Filter Pump

User Manual - Page 14