Maintainance guide – Electric scooters
1 Maintenance
To ensure you get the best possible performance and experience from your electric scooter, it is
important to do regular maintenance for important parts of the product.
Battery maintenance
Bearings, Screws, Brakes and Wheels
Storage and Cleaning
Your electric scooter will require some maintenance so please read and familiarize yourself with
this guide.
Battery maintenance
All batteries have a life cycle, and performance will decrease over time, however here are
some advice to maximize the life span of the battery.
Make sure that the battery is charged at regular intervals, even if you do not use the electric
scooter for a long time. This is to prevent damage to the battery, caused by low voltage over an
extended period.
Avoid draining the battery completely. It is best to charge while there is still power on it. This will
extend battery life. If the battery is constantly depleted, it will damage the battery (damaged
battery caused by wrong handling are not covered by the warranty).
If riding the electric scooter in cold or very hot areas, the battery time can be lower than when
riding in temperatures from 15-25° Celsius. This is not a failure on the batteries, but normal
behavior.
Please notice: Even a fully charged battery will run out of power if the electric scooter is not used
for a period. Expect a fully charged battery to keep power between 90 and 120 days in off mode,
before it is fully discharged. If only partially charged, this period is lower.
Please make sure the battery does not get above 50° Celsius, or below minus 10° Celsius for a
longer period. (e.g. don’t leave the electric scooter in a hot car in summer, do not put battery into
fire etc.) Low temperature (e.g. subzero temperature) can damage the battery cells.
Keep the Electric scooter away from open flame or other sources of heat to prevent the battery
from getting too hot. Also make sure not to leave the electric scooter at freezing temperatures.
Both heat and excessive cold can cause the battery to discharge.
Only use original charger or an official replacement, as different batteries may require specific
charger, and if using other chargers, this could cause damage to the product.
Do not overcharge and discharge the battery.
Please make sure to charge the battery before it is completely out of power, to avoid damaging
the battery cells. (damaged battery caused by wrong handling are not covered by the warranty)
It is forbidden to disassemble battery package. This is only to be handled by official service
repair centers and professionals.
Maintainance guide – Electric scooters
Bearings, Screws, brakes and Wheels
Your electric scooter is made up of moving parts, which in time, will be susceptible to wear and
tear.
Bearings and screws:
The electric scooter has sealed and dustproof bearings so that no lubrication is required. Check the
bearings for wear at regular intervals to avoid unsafe riding. Do not jump on and off and do not
apply excessive force otherwise to avoid damage to the bearings. This is not a sports electric
scooter.
Make sure that all screws are properly tightened to avoid unsafe situations.
Please check the screws regularly and tighten if they seem loose.
PICTURE IS ONLY AN EXAMPLE
Brakes:
Check the brake for wear at regular intervals to avoid unsafe riding. Do not apply excessive force
to avoid damage to the brake.
Electric scooter with disc brake will require adjustment over time and in the end will need to be
replaced, when worm down. Avoid using electric scooter when brakes are worn down, as this is
unsafe and will also damage the brake.
Wheels:
Check the wheels for wear at regular intervals to avoid unsafe riding.
Electric scooters come with different wheels but can in general be separated into tires with
inflatable inner tubes and solid wheels.
For inflatable tires, please make sure to keep the right pressure, as hard tires will last longer.
Maintainance guide – Electric scooters
2,5-3,5 bar / 35-45 PSI is considered as a reference value regarding the tire pressuere dependent
on personal driving comfort preferences.
If the wheel seems wobbly even after screws are tightened, the bearings might be
worn down and need replacement
PICTURE IS ONLY AN EXAMPLE
● Please make sure to check that the steering system is correctly adjusted and that
all connection components are firmly secured and not broken before riding, refer
to handle assembly and safety instruction.
● Please read operation guide and warnings of correct techniques for use and
braking
● Always wear shoes.
● We highly recommend to always wear helmet/pads for your own protection.
● Self-locking nuts and other self- locking fixings may lose their effectiveness.
● All parts and materials of electric scooter cannot be changed, modifications of the
scooter are not allowed. If done, then warranty is void.
Storage and cleaning
If your Electric scooter gets dirty, please clean it with a damp cloth only, you may not use
pressured water-gun or running water, as this could damage vital parts. It is also possible to use
a little toothpaste if the dirt is stuck. Remember to clean with damp cloth after this.
Please make sure to keep the electric scooter turned off while cleaning it, and make sure to
cover the charging input to avoid problems with the electronics.
Make sure to dry the scooter with a towel, should it become wet.
Please notice: Do not use alcohol, gas, kerosene or other corrosive and volatile chemical
solvents. This can damage both the appearance and the internal structure of the electric
scooter.
Please store your Electric scooter in a dry and cool environment when not in use. Avoid
leaving it outdoors, as it is not made for use in wet areas. Nor is it good to expose to high
WARNING
Maintainance guide – Electric scooters
temperatures
caused by direct sun for a long time.
