Loading ...
Loading ...
Loading ...
© 2018 Spectrum Brands, Inc.
4 / 4
This procedure will delete all User Codes associated
with the lock, and the default Programming Code
(0000) and User Code (1234) will be restored.
1. Make sure the door is open and unlocked. Press and hold the
Reset button for 5 seconds, until you hear 3 long beeps.
2. Enter the default Programming Code (OOO0).
3. Press . You will hear one beep.
4. Press
0.
5. Press . The latch bolt will extend and retract to learn the
orientation of the door. If successful, you will hear 2 beeps. If
unsuccessful, you will hear 3 beeps (make sure the door is open
and unlocked and that you are using a fresh set of batteries).
6. Test the lock: Activate the screen. With the door open and
unlocked, press the Lock symbol. Make sure it locks the door.
7. Test the default User Code: Activate the screen. Touch the
random digits that appear. Enter the default User Code (123-
4), then press the Lock symbol. Make sure it unlocks the door.
The default Programming Code is 0000. It is
recommended that you change it to a code of your own.
The lock is pre-programmed with a default User Code of
1234. It is recommended that you delete this code.
How to restore default settings
System Alerts
Sound Lights Meaning
1 beep Successful operation.
2 beeps Successful programming.
3 beeps Operation error.
5 beeps
X-pattern
(13579)
lashes.
5 incorrect code entered within one
minute. Re-enter User Code after
45-second touchscreen lockout.
10 rapid beeps Low battery.
3 long beeps Default settings restored.
Lock
button
lashes
slowly.
Lock is in programming mode.
Regulatory Compliance
Important Safeguards
Troubleshooting
The lock cannot be locked or unlocked by the
touchscreen.
Make sure the lock is programmed with at least
one User Code and that the User Codes are not
disabled. If needed, restore the lock’s default
settings.
The touchscreen doesn’t respond when
touched.
Make sure the cables are properly connected,
and make sure the batteries are new and
installed correctly.
After the lock has been working normally,
the latch bolt locks up and the turnpiece will
not rotate.
Enter your Programming Code.
Press .. You will hear one beep.
Press
0
.
Press .. You will hear two beeps.
The latch bolt will extend and retract to learn
the orientation of the door. If successful, you
will hear 2 beeps. If unsuccessful, you will
hear 3 beeps (make sure the door is open and
unlocked and that you are using a fresh set of
batteries).
The door can be locked with the Lock
symbol, but the User Code will not unlock
the door.
Make sure the User Code is correct and that the
Lock symbol is pushed after entering the User
Code. If the door still won’t unlock, use a key
to unlock the door. Call technical support for
further troubleshooting.
When the door is closed and the Lock symbol
is pressed to lock the door, the lock beeps 3
times. When the door is open and the Lock
symbol is pressed to lock the door, the lock
doesn't beep.
Make sure that the hole in the door frame
behind the strike is drilled at least 1 inch (25
mm) deep. Also make sure the strike plate is
aligned with the latch bolt. If needed, reposition
the strike.
This product complies with standards established by the following regulatory bodies:
• Federal Communications Commission (FCC)
• Industry Canada
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
( 1 ) this device may not cause harmful interference, and
( 2 ) this device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT! Changes or modiications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
Industry Canada
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: ( 1 ) this device may not cause interference, and ( 2 ) this device must accept any
interference, including interference that may cause undesired operation of the device.
1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution
statements.
3. Remind all family members of safety precautions.
4. Restrict access to your lock’s interior assembly and
routinely check your settings to ensure they have
not been altered without your knowledge.
5. Protect your User Codes and Programming Code.
6. Dispose of used batteries according to local laws
and regulations.
CAUTION: Prevent unauthorized entry. This lock has
a pre-set User Code and Programming Code. Upon instal-
lation and set-up, replace both of these codes with your
own. Since anyone with access to the interior assembly
can reset the lock and change the User Codes, you must
restrict access to the interior assembly and routinely
check the User Codes to ensure they have not been
altered without your knowledge.
WARNING: This Manufacturer advises that no lock
can provide complete security by itself. This lock may
be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute
for caution, awareness of your environment, and common
sense. Builder’s hardware is available in multiple perfor-
mance grades to suit the application. In order to enhance
security and reduce risk, you should consult a qualiied
locksmith or other security professional.
7
Quick Setup and Use
How to add User Codes
A total of 30 User Codes may be programmed. Do not
program a User Code that is the same as your
Programming Code.
CAUTION: A User Code is used to unlock the door
while a Programming Code is a password for making
changes to the lock features.
1. Make sure the lock is unlocked and the door is open.
2. Enter your Programming Code - for new installation, default
is 0000.
3. Press . You will hear one beep.
4. Press
1
.
5. Press . You will hear one beep.
6. Enter a new User Code. It must be 410 digits.
7. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
8. Test the code: While your door is open, lock it. Wake the
screen and touch the random lit digits.Enter your new User
Code, then press the Lock symbol. The door should unlock.
How to delete all User Codes
CAUTION: A User Code is used to unlock the door
while a Programming Code is a password for making
changes to the lock features.
1. Make sure the lock is unlocked and the door is open.
2. Enter your Programming Code - for new installation, default
is 0000.
3. Press . You will hear one beep.
4. Press
3
.
5. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
For a new installation, this will delete the default
User Code 1234. For subsequent instances,
this will delete all User Codes in the lock.
Now the lock can only be operated by the key and
turnpiece until a new User Code is added in step B.
How to change your Programming Code
The Programming Code will not unlock your door. It is
an added security feature that is used to set up all
functions.
The default Programming Code is 0000. It is
recommended that you change it to a code of
your own.
1. Make sure the lock is unlocked and the door is open.
2. Enter your Programming Code - for new installation, default
is 0000.
3. Press . You will hear one beep.
4. Press
4
.
5. Press . You will hear one beep.
6. Enter a new Programming Code. It must be between 4 and
10 digits.
7. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
BA C
8
Additional Programming Features
How to change Auto-Lock time delay
You can set the Auto-Lock time delay
between 10 and 99 seconds.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Programming Code.
3. Press . You will hear one beep.
4. Press
6.
5. Press . You will hear one beep.
6. Enter time between 10 and 99 seconds.
7. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
How to enable/disable Auto-Lock
The Auto-Lock feature automatically re-locks your door
30 seconds after unlocking. This feature is o by default.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Programming Code.
3. Press . You will hear one beep.
4. Press
5
.
5. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
How to add a one-time User Code
A one-time user code may be used only once, and
then it will be deleted immediately after use.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Programming Code.
3. Press . You will hear one beep.
4. Press
8
.
5. Press . You will hear one beep.
6. Enter a new User Code. It must be between 4 and 10 digits.
7. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
How to delete individual User Codes
The lock is pre-programmed with a default
User Code of 1234. It is recommended
that you delete this code.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Programming Code.
3. Press . You will hear one beep.
4. Press
2.
5. Press . You will hear one beep.
6. Enter the User Code you wish to delete.
7. Press . You will hear two beeps if successful. If you hear three
beeps, it was unsuccessful. Repeat from step 1 slowly.
8. Test the code: While your door is open, lock it. Enter the User Code,
then press the Lock symbol. The door should not unlock.
How to enable/disable User Codes
If User Codes are disabled (example: when you go
on vacation), the lock can only be operated by the
key and turnpiece until they are enabled again.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Programming Code.
3. Press . You will hear one beep.
4. Press
7
.
5. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
Move swiftly during programming. If no digit is pressed for 10 seconds, the touchscreen will turn o and you will need to restart the procedure.
Default Codes and Uses
Use
Default
(new lock only)
Programming
Code
A password to
make changes to
feature settings
0000
User Code
A code to unlock
the lock
1234