door frame
Make sure hole in door frame is drilled a
minimum of 1” (25 mm) deep.
Required tools
Ruler4 AA Batteries
Hammer
Wood
block
Pliers
Phillips screwdriver
Additional Tools (depending on application)
If drilling a new door, use the supplied template and the complete
door drilling instructions available at www.kwikset.com/doorprep
Note: Additional door preparation may be
required for doors with 11/2" (38 mm) holes.
Consult the deadbolt drilling instructions at
www.kwikset.com/doorprep
or
backset
Measure to conirm that the hole in
the door is either 21/8" (54 mm) or
11/2" (38 mm).
Measure to conirm that the backset is
either 23/8" or 23/4" (60 or 70 mm).
23/8" or 23/4"
60 or 70 mm
13/8"– 13/4"
35 mm or 44 mm
Measure to conirm that the hole in
the door edge is 1" (25 mm).
Measure to conirm that the
door is either 13/8" or 13/4"
(35 mm or 44 mm) thick.
A
A B C
D
B C D
21/8"
54 mm
11/2"
38 mm
1"
25 mm
1
Prepare the door and check dimensions
2
Install the latch and strike
Latch
Exterior Assembly
Interior Cover
Strike Cylinder
A
E
J K L M
F G H
B C D
Parts in the box
Drive-In Collar
Keys
Latch and
Strike Screws
Mounting Plate
Interior Assembly
Screws
Interior
Assembly
Mounting Plate
Screws
Align tabs with
holes in collar.
A
A
A
K (2x)
K (2x)
B
180°
Is the door edge chiseled?
Is the slotted hole centered in the door hole?
Hold the latch in front of the door hole, with
the latch face lush against the door edge.
YES
YES
NO
NO
Install latch in door with
supplied screws.
No adjustment is
required. Proceed
to next step.
slotted hole
is centered
slotted hole is
NOT centered
Rotate latch face as
shown to extend latch.
Use a lathead screwdriver to
lift tabs on collar of rectangular
face to remove it from latch.
Install drive-in collar.
Install latch in door with
wood block and hammer.
Install strike on the door frame.
IMPORTANT: Make sure the latch bolt is fully
retracted (in the unlocked position).
or
chiseled
not
chiseled
or
Make sure
slotted hole is at
bottom of latch.
Make sure
slotted hole is at
bottom of latch.
Ensure collar
snaps into place.
Pull collar to test
for tight it.
unlocked
C
A
1 / 4
ENGLISH
66877002
Rev 02
Installation and User Guide
Kwikset
Technical Support
1-800-327-5625
www.kwikset.com
275 Touchscreen
Electronic Deadbolt
4
Install exterior assembly
Install the cylinder into the exterior assembly.
A
IMPORTANT: Make sure the torque
blade is in the horizontal position.
D
Secure the mounting plate with the supplied screws.
G
Insert the torque blade through the
horizontal slot in the latch.
E
Insert the key and test the latch for smooth operation.
H
Remove the key and make sure the latch
bolt is still in the unlocked position.
I
Push the torque blade through the center
hole in the mounting plate and send the
cable through the bottom hole.
F
Route the cable below the latch.
B
IMPORTANT: Make sure the latch is fully
retracted (in the unlocked position).
C
cable
exterior side
of door
horizontal
horizontal
slot
unlocked
unlocked
torque blade in
center hole
cable in
bottom hole
interior side of door
Keep
parallel to
door edge.
If latch does
not operate
smoothly,
adjust screws.
E
G
F
M (2x)
D
2 / 4
Diameter is 2-1/8" (54 mm) Diameter is 1-1/2" (38 mm)
21/8"
54 mm
11/2"
38 mm
No adjustment is required.
Proceed to step 4.
or
What is the diameter of the hole in the door?
A
B
Remove adapter ring from exterior assembly:
Use pliers to remove two tabs from mounting plate:
tabs
1. Remove gasket. 2. Remove adapter
ring from gasket.
3. Reinstall gasket,
ensuring tight seal.
E
G
3
Prepare keypad and mounting plate (only for doors with smaller holes)
3 / 4
5
6
Install interior assembly
Set locking and unlocking direction
Remove the battery cover.
A
Align the colored edges of the connectors
and ensure a tight cable connection.
D
Test the turnpiece for smooth rotation.
G
IMPORTANT: Rotate the turnpiece AWAY
from the door edge and make sure the latch
is fully retracted (in the unlocked position).
E
Secure the interior assembly with
the supplied screws.
H
Reinstall battery cover and make sure the
latch is still in the unlocked position.
I
Make sure the torque blade is still in the horizontal
position and install the interior assembly.
F
Load 4 AA batteries into the interior
assembly. For best results, use new, non-
rechargeable Alkaline batteries only.
B
Press and hold the Reset button on the interior
assembly for 5 seconds, until you hear 3 long beeps.
C
unlocked
Ensure correct
polarity.
If turnpiece
doesn’t rotate,
repeat steps 5E
and 5F, making
sure to rotate
the turnpiece
AWAY from the
door edge.
horizontal
door
edge
Note: Turnpiece
may move
on its own.
45°
H
H
L (3x)
J
J
While the door is OPEN and UNLOCKED, activate the screen. To activate the screen, touch screen with
palm or back of hand until digits illuminate.
If successful, activate the screen.
Press the Lock symbol. The latch bolt will extend to lock.
The latch bolt will extend and retract.
If successful, you will hear 2 beeps.
If unsuccessful, you will hear 3 beeps. If
batteries are low, you will hear 10 beeps.
BA
D
C
If unsuccessful,
make sure the door
is unlocked and that
you are using a fresh
set of batteries.
Activate the screen. Touch the random digits that appear (this is a security feature
that ensures ingerprints are spread around the entire screen).
Enter the default User Code (1234), then press the Lock symbol. The door will unlock.
IMPORTANT: It is recommended that you replace the default
Programming Code and default User Code with codes of your own. See page 4.
During normal
operation, press the
Lock symbol to lock
the door.
E
= Lock symbol
Touch random
digits.
Enter User Code.
Default: 1234
Press Lock symbol.
During normal
operation, press
the Lock symbol
after entering
your user code to
unlock the door.
This is your default
Programming Code.
Enter the following code to teach
the lock the orientation of the door:
1. Press 0000.
2. Press . You will hear one beep.
3. Press 0.
4. Press .
unlocked
© 2018 Spectrum Brands, Inc.
4 / 4
This procedure will delete all User Codes associated
with the lock, and the default Programming Code
(0000) and User Code (1234) will be restored.
1. Make sure the door is open and unlocked. Press and hold the
Reset button for 5 seconds, until you hear 3 long beeps.
2. Enter the default Programming Code (OOO0).
3. Press . You will hear one beep.
4. Press
0.
5. Press . The latch bolt will extend and retract to learn the
orientation of the door. If successful, you will hear 2 beeps. If
unsuccessful, you will hear 3 beeps (make sure the door is open
and unlocked and that you are using a fresh set of batteries).
6. Test the lock: Activate the screen. With the door open and
unlocked, press the Lock symbol. Make sure it locks the door.
7. Test the default User Code: Activate the screen. Touch the
random digits that appear. Enter the default User Code (123-
4), then press the Lock symbol. Make sure it unlocks the door.
The default Programming Code is 0000. It is
recommended that you change it to a code of your own.
The lock is pre-programmed with a default User Code of
1234. It is recommended that you delete this code.
How to restore default settings
System Alerts
Sound Lights Meaning
1 beep Successful operation.
2 beeps Successful programming.
3 beeps Operation error.
5 beeps
X-pattern
(13579)
lashes.
5 incorrect code entered within one
minute. Re-enter User Code after
45-second touchscreen lockout.
10 rapid beeps Low battery.
3 long beeps Default settings restored.
Lock
button
lashes
slowly.
Lock is in programming mode.
Regulatory Compliance
Important Safeguards
Troubleshooting
The lock cannot be locked or unlocked by the
touchscreen.
Make sure the lock is programmed with at least
one User Code and that the User Codes are not
disabled. If needed, restore the lock’s default
settings.
The touchscreen doesn’t respond when
touched.
Make sure the cables are properly connected,
and make sure the batteries are new and
installed correctly.
After the lock has been working normally,
the latch bolt locks up and the turnpiece will
not rotate.
Enter your Programming Code.
Press .. You will hear one beep.
Press
0
.
Press .. You will hear two beeps.
The latch bolt will extend and retract to learn
the orientation of the door. If successful, you
will hear 2 beeps. If unsuccessful, you will
hear 3 beeps (make sure the door is open and
unlocked and that you are using a fresh set of
batteries).
The door can be locked with the Lock
symbol, but the User Code will not unlock
the door.
Make sure the User Code is correct and that the
Lock symbol is pushed after entering the User
Code. If the door still won’t unlock, use a key
to unlock the door. Call technical support for
further troubleshooting.
When the door is closed and the Lock symbol
is pressed to lock the door, the lock beeps 3
times. When the door is open and the Lock
symbol is pressed to lock the door, the lock
doesn't beep.
Make sure that the hole in the door frame
behind the strike is drilled at least 1 inch (25
mm) deep. Also make sure the strike plate is
aligned with the latch bolt. If needed, reposition
the strike.
This product complies with standards established by the following regulatory bodies:
• Federal Communications Commission (FCC)
• Industry Canada
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
( 1 ) this device may not cause harmful interference, and
( 2 ) this device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT! Changes or modiications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
Industry Canada
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: ( 1 ) this device may not cause interference, and ( 2 ) this device must accept any
interference, including interference that may cause undesired operation of the device.
1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution
statements.
3. Remind all family members of safety precautions.
4. Restrict access to your lock’s interior assembly and
routinely check your settings to ensure they have
not been altered without your knowledge.
5. Protect your User Codes and Programming Code.
6. Dispose of used batteries according to local laws
and regulations.
CAUTION: Prevent unauthorized entry. This lock has
a pre-set User Code and Programming Code. Upon instal-
lation and set-up, replace both of these codes with your
own. Since anyone with access to the interior assembly
can reset the lock and change the User Codes, you must
restrict access to the interior assembly and routinely
check the User Codes to ensure they have not been
altered without your knowledge.
WARNING: This Manufacturer advises that no lock
can provide complete security by itself. This lock may
be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute
for caution, awareness of your environment, and common
sense. Builder’s hardware is available in multiple perfor-
mance grades to suit the application. In order to enhance
security and reduce risk, you should consult a qualiied
locksmith or other security professional.
7
Quick Setup and Use
How to add User Codes
A total of 30 User Codes may be programmed. Do not
program a User Code that is the same as your
Programming Code.
CAUTION: A User Code is used to unlock the door
while a Programming Code is a password for making
changes to the lock features.
1. Make sure the lock is unlocked and the door is open.
2. Enter your Programming Code - for new installation, default
is 0000.
3. Press . You will hear one beep.
4. Press
1
.
5. Press . You will hear one beep.
6. Enter a new User Code. It must be 410 digits.
7. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
8. Test the code: While your door is open, lock it. Wake the
screen and touch the random lit digits.Enter your new User
Code, then press the Lock symbol. The door should unlock.
How to delete all User Codes
CAUTION: A User Code is used to unlock the door
while a Programming Code is a password for making
changes to the lock features.
1. Make sure the lock is unlocked and the door is open.
2. Enter your Programming Code - for new installation, default
is 0000.
3. Press . You will hear one beep.
4. Press
3
.
5. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
For a new installation, this will delete the default
User Code 1234. For subsequent instances,
this will delete all User Codes in the lock.
Now the lock can only be operated by the key and
turnpiece until a new User Code is added in step B.
How to change your Programming Code
The Programming Code will not unlock your door. It is
an added security feature that is used to set up all
functions.
The default Programming Code is 0000. It is
recommended that you change it to a code of
your own.
1. Make sure the lock is unlocked and the door is open.
2. Enter your Programming Code - for new installation, default
is 0000.
3. Press . You will hear one beep.
4. Press
4
.
5. Press . You will hear one beep.
6. Enter a new Programming Code. It must be between 4 and
10 digits.
7. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
BA C
8
Additional Programming Features
How to change Auto-Lock time delay
You can set the Auto-Lock time delay
between 10 and 99 seconds.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Programming Code.
3. Press . You will hear one beep.
4. Press
6.
5. Press . You will hear one beep.
6. Enter time between 10 and 99 seconds.
7. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
How to enable/disable Auto-Lock
The Auto-Lock feature automatically re-locks your door
30 seconds after unlocking. This feature is o by default.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Programming Code.
3. Press . You will hear one beep.
4. Press
5
.
5. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
How to add a one-time User Code
A one-time user code may be used only once, and
then it will be deleted immediately after use.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Programming Code.
3. Press . You will hear one beep.
4. Press
8
.
5. Press . You will hear one beep.
6. Enter a new User Code. It must be between 4 and 10 digits.
7. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
How to delete individual User Codes
The lock is pre-programmed with a default
User Code of 1234. It is recommended
that you delete this code.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Programming Code.
3. Press . You will hear one beep.
4. Press
2.
5. Press . You will hear one beep.
6. Enter the User Code you wish to delete.
7. Press . You will hear two beeps if successful. If you hear three
beeps, it was unsuccessful. Repeat from step 1 slowly.
8. Test the code: While your door is open, lock it. Enter the User Code,
then press the Lock symbol. The door should not unlock.
How to enable/disable User Codes
If User Codes are disabled (example: when you go
on vacation), the lock can only be operated by the
key and turnpiece until they are enabled again.
1. Make sure the lock is unlocked and the door is open.
2. Enter your existing Programming Code.
3. Press . You will hear one beep.
4. Press
7
.
5. Press . You will hear two beeps if successful. If you hear
three beeps, it was unsuccessful. Repeat from step 1 slowly.
Move swiftly during programming. If no digit is pressed for 10 seconds, the touchscreen will turn o and you will need to restart the procedure.
Default Codes and Uses
Use
Default
(new lock only)
Programming
Code
A password to
make changes to
feature settings
0000
User Code
A code to unlock
the lock
1234
