User Manual Kwikset HC620 CNT ZW700 15 SMT RCAL RCS CP Home Connect 620 Contemporary Keypad Connected Smart Lock

Kwikset HC620 CNT ZW700 15 SMT RCAL RCS CP Home Connect 620 Contemporary Keypad Connected Smart Lock - Use Manual - Use Guide PDF.
Documents: Go to donwload!
User Manual
  • User Manual - (English, Spanish)
Installation Instruction
  • Instructions to re-key a SmartKey Security lock - (English)

file thumbnail

User manual Smart Lock for Kwikset HC620 CNT ZW700 15 SMT RCAL RCS CP

Table of contents

  • Parts in the box
  • Required tools
  • Installation
  • Smart home system setup
  • Reference guide

Install the latch

  • Extend the latch bolt . 
  • UP is on top .
  •  If the D - shaped hole is not centered in the door hole , rotate the latch face to extend the latch. 

Install the exterior assembly 

  •  If the hole in the door is 2-1 / 8 " ( 54 mm ) , install the adapter ring . If the hole in the door is 1-1 / 2 " ( 38 mm ) , the adapter ring is not needed . 
  • Cable goes under the latch .
  • Route the cable through the center hole of the mounting plate. 
  • Push the cable into the bottom hole of the mounting plate . 
  • Insert the key and test the latch . If the latch does not extend or retract smoothly , adjust the screws .

Install the interior assembly 

  • Make sure the turnpiece shaft is pointing up as shown below.
  • If the turnpiece shaft is not pointing up , put the cover back on and rotate the turnpiece until you hear a click .
  • Connect the cable . Ensure a tight cable connection . 
  • Lay cable flat inside the bottom of the interior housing . 
  • Ensure the spindle fully engages with the turnpiece shaft .

Perform the door handing process

Install 4 AA batteries into the battery pack .

The latch will retract and extend to learn the orientation of the door . Then the status LED will indicate success or failure .

  • GREEN : Successful . Proceed to the next step .
  • RED: Unsuccessful . Make sure the lock interior and batteries are correctly installed . Perform step 5 again . If your second attempt is still unsuccessful , follow the Manual Door Handing instructions on page 19 . 
  • NOTE :  The lock will auto - hand again after the first time the door . is locked or unlocked using the keypad or app . This is to confirm the door orientation .

Add the lock to your smart home system 

  •  Initiate the process to add the lock to your system at your smart home controller . Refer to your smart home system instructions for more information .
  • If prompted by your smart home system to add the lock , press button " A " on the lock interior one time . The red LED will illuminate when the lock enters Add Mode .
  • At this time , you may be prompted by your smart home system to enter the 5 - digit PIN found on the label of the interior assembly . If not , proceed to step D. 
  • If successful , re - name the lock in your system ( if applicable ) . If unsuccessful , follow your system's instructions to remove the lock from the controller and any other network , then press button " A " on the lock one time . Perform steps A - C again . 


Newest Added: 914CNT ZB 15 916CNT ZB 15 788SAL SQT 15 730SAL SQT 15 740SAL SQT 15 SMT

Tags: Kwikset Premis, Kwikset Electronic Doorlock, Kwikset 914, Kwikset Home Connect 620, Kwikset Smartcode 914

Kwikset HC620 CNT ZW700 15 SMT RCAL RCS CP | Pages: 48 | Created on: 2021-03-02 | File type: PDF | Filename: 17532637_hc620-trl-zw700-15-smt-rcal-rcs-cp.pdf | Size: 15.44 MB | Language: English, Spanish | Other documents: 1 files.

Download User Manual

Product Infomation and Reviews - HC620 CNT ZW700 15 SMT RCAL RCS CP photo

HC620 CNT ZW700 15 SMT RCAL RCS CP Photo

T: @manualsFile

https://manualsFile.com