Loading ...
Loading ...
Loading ...
49-5000430 Rev. 4 5
ENGLISH
CONTROLS
Controls
NOTE: When the bucket is full or removed, the controls cannot be set.
1. Power Pad
Press to turn the dehumidifier on and off.
NOTE: Turning off the power by pressing the Power button does
NOT disconnect the appliance from power supply.
"ÏäñÜóèèçÙäç
Controls the fan speed.
Press to select either High, Medium, Low, or Smart Dry fan speed.
Set the fan control to High for maximum moisture removal. When
the humidity has been reduced and quiet operation is preferred,
set the fan control to Medium or Low.
Smart Dry compares the set humidity level with the actual
humidity and adjusts the fan speed automatically.
3. Display
Shows the set % humidity level while setting, then shows the
actual (+/– 5% accuracy) room % humidity level.
$Ñøðìçì÷üÜè÷Ìòñ÷õòïÙäçö
Ýëèëøðìçì÷üïèùèïæäñåèöè÷úì÷ëìñäõäñêèòé#%]ÛѤÛèïä÷ìùè
Ñøðìçì÷ü¥÷ò( ]ÛѤÛèïä÷ìùèÑøðìçì÷ü¥ìñ%]ìñæõèðèñ÷öòõ
in Nonstop mode for continuous operation. To set the unit for
continuous operation, press the
pad until the “Nonstop”
indicator light is illuminated.
NOTE: If Nonstop is selected, the dehumidifier will operate
continuously at its maximum dehumidification settings if
attached to a hose to drain or until the bucket is full.
For drier air, press the
pad and set to a lower percent value (%).
For damper air, press the pad and set to a higher percent value (%).
When you first use the dehumidifier, set the humidity control
to 45% or 50%. Allow at least 24 hours for the dehumidifier
to achieve the humidity level. If you still have damper air than
desired, set the humidity level to a lower setting or select
Nonstop for maximum dehumidification.
5. Filter Timer
After 250 hours of operation, the Clean the Filter indicator light will
glow to remind you to clean the filter. Remove the filter and clean it.
Press and hold Filter button for 3 seconds to reset the filter
reminder. See the Care and Cleaning section.
6. Delay Off
While the dehumidifier is operating press the Delay button.
Press the
/ buttons to select the number of hours you want
the dehumidifier to continue to operate before turning Off.
NOTE: After displaying the time, the Display will revert to
showing the current humidity after 5 seconds have passed.
Pressing the Delay button will display the number of hours left on
the delay.
Delay On
While the dehumidifier is off press the Delay button.
Press the
/ buttons to select the number of hours you
want the dehumidifier to remain off before turning On.
NOTE: The display will show the number of hours left until the
dehumidifier turns on.
To cancel the Delay:
Press the Delay button once, the hours remaining on the Delay
will appear on the display. Press the Delay button again and the
Delay will be cancelled.
7. Empty Indicator
The “Empty” indicator will blink when the bucket is ready to be
emptied, or when the bucket is removed and/or not replaced in
the proper position.
Appearance may vary by model.
Other Features
Alarm
If the bucket is full or missing, an alarm will sound for about 10 seconds to
remind you to empty and replace the bucket.
Auto Shut Off
The Water Level Control Switch shuts off the dehumidifier when the bucket
is full, or when the bucket is removed and/or not replaced in the proper
position.
NOTE: The fan and compressor will stop running as soon as the bucket is
removed. The alarm will sound if the bucket is not replaced in the proper
position after 3 minutes.
Auto Defrost
When frost builds up on the evaporator coils, the compressor will cycle off
and the fan will continue to run until the frost disappears.
Power Outage
In the case of a power outage or interruption, the unit will automatically
restart, in the settings last used, after the power is restored.
Loading ...
Loading ...
Loading ...