Kwikset 939 WIFI TSCR 15 Touchscreen

User Guide - Transcript

• Page 1 - English - : Parts List Mounting | Adapter Exterior Assembly Interior Assembly WI-FI TOUCHSCREEN SMART LOCK For Latch / Strike Strike 03809 SmartKey Installation and User Guide i hm Teal If drilling a new door. use the supplied template and the complete door drilling instructions available at kwikset.com/doorprep Required tools Phillips head screwdriver 1-800-327-5625 www.kwikset.com 49191 64109 Additional Tools (depending on application) Hammer O... block Chisel > po pom Poo poo “B” is not included. If needed. please contact Kwikset to order a drive-in latch for your lock. a Prepare the door and check dimensions Make sure your door is compatible. If you have a standard deadbolt mounted B separately from the handle below it. your door is compatible. Remove your existing deadbolt from your door. Compatible Not Compatible Not Compatible Integrated C Measure to confirm that the hole in the door is either 2-1/8" (54 mm) or 1-1/2" (38 mm). Measure to confirm that the door is between 1-3/8" and 2" (35 mm and 51 mm) thick. Measure to confirm that the backset is Measure to confirm that the hole FE either 2-3/8" or 2-3/4" (60 or 70 mm). in the door edge is 1" (25 mm). Note: Additional door preparation may be required for doors with 1-1/2" (38 mm) holes. 1-3/8" -2" Consult the deadbolt drilling instructions at kwikset.com/doorprep 2-3/8" or 2-3/4" 60 or 70 mm - (2x) (2x) (2x) at 03809 actualsize || 46780 actual size AA | Isthe door edge chiseled? B Hold the latch in front of the door hole. with the latch D Which latch are you installing? face flush against the door edge. NO Latch “A Use latch “A”. If the latch bolt is not already extended. extend the latch bolt as shown. Use latch “B” (not included). If the latch bolt is not already extended. extend the latch bolt as shown. Cc Is the D-shaped hole centered in the door hole? D-shaped hole No adjustment is required. Proceed to next step. D-shaped hole Rotate latch face as shown to extend latch. *Use longer E Install the strike on the door frame. J\ Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep. Longer screws install closest to the door jamb. door frame
• Page 2 - English - : Ey Install the exterior keypad A What is the diameter of the hole in the door? Diameter is 2-1/8" Adapter Ring is required for installation. Install on Exterior Assembly. Diameter is 1-1/2" © 48654 (2x) actual size D Install the exterior keypad and mounting plate. Adapter Ring is not needed for installation and may be discarded. Locate the screws for step 3D and keep them within reach. Remove the mounting plate from the interior assembly. 4 Install the interior assembly © Remove the interior cover from the interior assembly. If the turnpiece shaft is pointing down. place the cover back onto the interior assembly and rotate the turnpiece until you hear it click. You may need to apply some force. Once the turnpiece shaft is correctly oriented. remove the cover again. Keep paralleltothe edge ofthedoor. e Tighten screws evenly. DO NOT over tighten screws. Make sure turn piece shaft is rotated as shown. If turnpiece shaft is not oriented correctly. put the cover back on and rotate the turnpiece as shown in step C. Do not install until step 5. A\ Support the exterior assembly during mounting plate installation. The cable goes underneath the latch. Ensure the turnpiece shaft is pointing up. and remove the interior cover and B Install the interior assembly onto the mounting plate. battery pack from the interior assembly. Ensure tight cable connection. flat inside the Ensure you are using the correct screws. Using incorrect screws will damage the product. Lay the excess cable the interior housing. Route the cable through the center hole. then push it into the bottom hole. Insert the key and test the latch. If the il YY extend or WS retract smoothly. adjust the screws. Wr latch does not Remove the key when finished. and make sure the latch bolt is fully extended. For at (2x) Bag | 49191 actual size
• Page 3 - English - : 5 Install the batteries and perform the door handing process This step will teach your lock the orientation of your door and is crucial to lock operation. After a few seconds. the latch bolt will retract and extend on its own to learn the orientation of the door. This is called the door handing process. and it is crucial to lock operation. With the door open. install the battery pack to initiate auto-handing. Install 4 AA batteries in the battery pack. Once the door handing process is complete. the touchscreen will indicate success or failure. Success Failure flashing checkmark flashing "X" symbol and single pattern column of digits If the touchscreen indicates a failure. make sure the lock interior and batteries are correctly installed. Perform step 5B again. A\ Ensure correct polarity. For best results. use new. non-rechargeable Alkaline batteries only. If the door handing process is still unsuccessful after a second attempt. see the Manual Door Handing section on page 4. 6 Test the lock and check door alignment Turn the key 180° to retract the latch. Ensure that the door unlocks smoothly. Close the door. Insert and rotate the key to lock the door. Ensure that the door locks smoothly. Turn the key 180° to retract the latch. Ensure that the latch retracts smoothly. With the door open. insert the key to extend the latch. Ensure that the latch extends smoothly. If your door does not lock and unlock smoothly. make sure you replaced your previous latch and strike with those supplied in the box. If you still experience locking errors. call Kwikset Support to order a Warped Door Service Kit. Kwikset Support: 1-800-327-5625 ca Install the interior cover For (nest (1x) Pun (3x) Bag 68611 64109 Important Information about the interior cover actual size actual size The window on the interior cover is unlocked by default for easier access to the battery pack and buttons. For additional security. you may choose to lock the window by installing the security screw. Ensure you are using the correct screws. Using incorrect screws will damage the product. When the window is locked. you will need to remove the entire interior cover and screws to access the battery pack and buttons. Cover Installation Battery Pack Access © Install cover. Install If the window is If the window screws. unlocked. slide is locked. Note: You may a. up the window remove the need to rotate 64109 (3x) to access the interior cover the turn piece Ke /\ battery pack. and screws >t Ensure you are usin to align with the the correct screws. i: to access the ; turn piece Bia Tacsrree batt k. turn piece shaft. eaaieiece pea t attery pac shaft damage the product. L\ The Kwikset app is needed to use this lock. If this lock was professionally installed (or installed by someone other than the homeownen). make sure this step is performed by the homeowner. Fy Download the app and create an account Download the the QR code or visiting on your smartphone. Kwikset app by scanning www.kwikset.com/app Create your account and follow the setup instructions in the Kwikset app.
• Page 4 - English - : Reference Guide Halo Touchscreen at a Glance System Alerts Touchscreen Button “A” Interior (cover removed) Button “B” "X" pattern flashes once with one beep*. One incorrect code Re-enter code. “X” pattern flashes three times with three No user code programmed. Program at least one user code. "X" pattern flashes red 15 times with 15 beeps* Three incorrect codes Re-enter code after 60 second keypad lockout. Checkmark and lock symbols flash simultaneously five times with five beeps”. Low battery. Replace batteries. Checkmark and lock symbols alternate flashing five times with Door jammed while attempting to lock. Manually re-lock door. If needed. reposition five beeps*. Remove battery pack. reconnect the interior to the exterior. then reinstall battery pack. Interior assembly is disconnected from Lock beeps continuously. *Beeping sounds will only be heard if Lock Sounds have not been disabled in the app. Status LED colors These features can be adjusted in some smart home apps. Manual Door Handing If needed. the door handing process can be initiated manually. This is useful if the lock is being moved to a different door. 1 Remove battery pack. L] 2 Press and HOLD the Program button while reinserting the battery pack. Release the Program button after 3 seconds. The status LED will flash red and green. Color Lock Status Action successful Green (solid) Green (blinking) Red (solid) Door handing process unsuccessful Action unsuccessful or incomplete Red (blinking) Low battery 4 The latch bolt will extend and retract to learn the orientation of the door. The LED will flash green if handing is successful or red if handing is unsuccessful. Blue (solid) Blue (blinking) Amber (solid) Bluetooth Pairing successful Bluetooth Pairing Mode Entering Network Reset mode Network or System Reset mode. Action required. Amber (blinking) System Reset Factory Reset Network Reset Network Reset will delete all Wi-Fi settings. Bluetooth pairings. user associations. and remove the lock from the account. System Reset will delete all access codes and lock settings including lock handing. The lock will run the handing process at the end of the System Reset. Factory Reset will delete all Wi-Fi settings. Bluetooth pairings. user associations. remove the lock from the account. and reset all lock settings including handing. 1 Press and HOLD “A” for 10 seconds. You will hear 1 short beep and see an amber LED. 2 Release “A.” You willseea blinking amber LED to indicate it is in network reset mode. 2 Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps Status and the status LED LED flashes red. battery pack. 2 Press and release the Program button to confirm system reset. 1 Press “A” 10 times. You will hear 1 short beep and seea blinking amber LED to indicate itis in system reset mode. Note: After 3 seconds. you will hear 1 short beep Status and see a blue 6 LED LED. You should s continue to hold “A” to enter network reset mode. If successful. you will hear 1 long beep and see a green LED. and the reset process 4 The latch will retract and extend to learn the orientation 3 Press the Program button once more. The LED will Successful: Unsuccessful: Press and release the 4 If successful. you will hear 1 long Program button to confirm network reset. The Program button must be pressed within 10 seconds of releasing "A" or the function will time out. beep and see a green LED. If unsuccessful. you will hear 5 rapid beeps and see a blinking red LED. If unsuccessful. repeat from step 1. Successful: Unsuccessful: will begin. During the reset process. the LED will blink green/red a few times and will beep when complete. If unsuccessful. you will hear 5 rapid beeps and see a blinking red LED. If unsuccessful. repeat from Troubleshooting A complete Halo Touchscreen Programming and Troubleshooting Guide is available at SmartKey Re-Keying Re-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information. Note: If Auto-Lock is enabled. remove the battery pack before re-keying your lock. flash green and red. and the auto-handing process will begin. of the door. The LED will flash green if auto-handing is successful or red if autohanding is unsuccessful. Important Safeguards Read all instructions in their entirety. Familiarize yourself with all warning and caution statements. Remind all family members of safety precautions. Protect your user codes. Dispose of used batteries according to local laws and regulations. A\ WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means. or evaded by entry elsewhere on the property. No lock can substitute for caution. awareness of your environment. and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk. you should consult a qualified locksmith or other security professional. © 2020 Spectrum Brands. Inc.