Loading ...
Loading ...
Loading ...
9
ENGLISH
(Original instructions)
Assembly
Warning! Before attempting any of the following
instructions, make sure that the appliance is
switched off and unplugged and the appliance is
cold and does not contain any water.
Attaching the handle (Fig. A)
• Slide the bottom end of the handle (8) into the top end of
the steam mop body (11) until it clicks into place.
Attaching the hand held steam cleaner
(Fig. B)
• Holding the back of the steam mop body (11) push the
hand held steam cleaner (5) firmly into the steam mop
body (11) making sure it sits correctly over the interface
(11a) and clicks securely into place.
Removing the hand held steam cleaner
(Fig. B)
• Push the release button (10) on the main body (11) and
lift the hand held steam cleaner (5) off the interface (11a)
and away from the main body (11).
Attaching a cleaning pad (Fig. C)
Replacement cleaning pads are available from your
BLACK+DECKER dealer :- (cat no. FSMP20-XJ).
• Place a cleaning pad (13) on the floor with the velcro
'loop' side facing up.
• Lightly press the steam mop down onto the cleaning pad
(13).
Note: This unit may be supplied with a standard floor
cleaning head (12) or a steam burst cleaning head (12a). In
either case use these instructions to fit a cleaning pad.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Removing a cleaning pad
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop.
Do not wear slippers or open toed footwear.
• Return the handle (8) to the upright position and turn the
steam mop 'OFF'.
• Wait until the steam mop cools down (approximately 5
minutes).
• Lift the steam mop away from the cleaning pad freeing it
from the velcro fastening.
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop with the handle (8) supported in
the upright position when stationary and make sure the
steam mop is turned off when not in use.
Filling the water tank (Fig. Q)
Note! Fill the water tank with clean tap water (Do not use any
additives or chemicals).
Note! In areas of hard water, the use of de-ionised water is
recommended.
• Open the filler cap (4) by flipping it up.
• Fill the water tank with water (Do not use any additives or
chemicals).
Warning! When filling, detach from main unit and maintain in
a horizontal position.
Warning! Your water tank has a 0.5 litre capacity. Do not
over fill the tank.
• Close the filler cap (4).
Note! Ensure the filler cap is firmly secured.
Attaching the carpet glider (12b) (For use on
carpets only)
• Place the carpet glider (12b) on the floor.
• Attach a cleaning pad to the floor cleaning head (12)
• Lightly press the steam mop down onto the carpet glider
(12b) until it clicks into place.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Removing the carpet glider
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
20a
�
21
�
21a
�
22
All
22a
All
22b
All
22c
All
23
All
23a
All
23b
�
23c
�
23d
�
24
�
25
N/A
28
ALL
FSMH1351SM
FSH13101SM
FSMH13151SM
FSMH13151SM
FSMH1321J
FSMH1321JSM
FSMH1321JMD
SETTINGS
FSMH1321
Loading ...
Loading ...
Loading ...