Loading ...
Loading ...
Loading ...
3. Shooting
45
G
J
You can select the adjustment mode to suit
the shooting conditions.
ATW (Auto Tracing White Balance)
This function adjusts the white balance
automatically to an appropriate level.
The white balance is automatically adjusted
when the color temperature of the light source
changes.
Press and hold the WHT BAL function button
(G) to display the direct menu (page 48)
and select ATW.
You can select the speed of adjustment
(five steps) using White Setting >ATW Speed
(page 74) in the Shooting menu of the full
menu.
[Tip]
You can freeze the current white balance setting by
assigning the ATW Hold function to an assignable
button (page 48), and pressing the assignable button
to temporarily pause ATW mode.
[Notes]
ATW cannot be used in Cine EI mode.
It may not be possible to adjust to the appropriate
color using ATW, depending on the lighting and
subject conditions.
Examples:
– When a single color dominates the subject, such as
sky, sea, ground, or flowers.
– When the color temperature is extremely high or
extremely low.
If the appropriate effect cannot be obtained because
the ATW auto tracking speed is slow or for other
reasons, run auto white balance.
Adjusting the White Balance
Manually
1 When white balance is set to ATW mode,
press and hold the WHT BAL function
button (G) to display the direct menu
(page 48), and select W:P, W:A, or W:B.
2 Select B, A, or PRESET using the WHT BAL
switch (J).
B: Memory B mode
A: Memory A mode
PRESET: Preset mode
[Tip]
ATW can be enabled for memory B by setting White
Setting >White Switch<B> (page 74) in the Shooting
menu of the full menu to ATW.
Memory A/Memory B mode
This mode adjusts the white balance to the
setting saved in memory A or B, respectively.
Preset mode
This mode adjusts the color temperature to a
preset value (factory default is 3200K).
Changing the default preset value
In preset mode, you can change an existing
preset value directly.
Press and hold the WHT BAL function button
(G) and select one of the following in the
direct menu.
Custom mode:
3200K, 4300K,
5600K, 6300K
Cine EI mode:
3200K, 4300K, 5500K
[Tip]
You can also assign Preset White Select to an assignable
button (page 48), and press the button to change the
setting.
Custom mode: 3200K 4300K 5600K 6300K
3200K…
Cine EI mode: 3200K 4300K 5500K 3200K…
Changing the color temperature
1 Press the WHT BAL function button (G) so
that the color temperature value is
displayed on a white background.
2 Turn the multi-function dial to adjust the
value.
[Tips]
In preset mode, you can set the value in 100K units.
In memory mode, you can set the value in 20K
increments in the range 2000K to 5600K. Values
above 5600K can be set at intervals equal to the
amount of color change (mired) from 5580K to
5600K. You can also adjust the tint value using White
(page 74) >Tint in the Shooting menu of the full
menu.
Running auto white balance
The white balance to save in memory A/
memory B mode is configured automatically.
1 Select memory A mode or memory B
mode.
2 Place white paper (or other object) in a
location with the same lighting source
and conditions as the subject, then zoom
in on the paper to show white on the
screen.
3 Adjust the brightness.
Adjust the iris using the procedure in
“Adjusting the iris manually” (page 42).
4 Press the WB SET button (page 4).
If auto white balance is run in memory
mode, the adjustment value is saved in
the memory (A or B) selected in step1.
If auto white balance is run in ATW
mode, the white balance adjustment
returns to the ATW mode white balance
when adjustment ends.
[Note]
If the adjustment is not successful, an error message is
displayed on the screen for about three seconds. If the
error message persists after repeated attempts to set
white balance, contact your Sony service representative.
Adjusting for Natural Colors (White Balance)
Loading ...
Loading ...
Loading ...